Single lens reflex and its parameters
The following are some of the parameters and related points that affect the DSLR film output: ###1. White Balance 1. ** Dark Blue ** - When the ambient light was different, the white balance needed to be adjusted according to the ambient light. It was generally set between 4000K and 5000K of CT color temperature. When the ambient light was warm, the photo taken would not be blue. 2. ** White balance in adjustment of other hue related parameters ** - The white balance could be adjusted according to personal style in the color adjustment of quiet gray tone, rich warm tone, bleached tone, low saturated natural tone, net red premium blue, warm tone, daily film, etc. ###2. Compensation for exposure 1. ** Tranquil Gray ** - You can adjust the exposure compensation according to your personal style. It is recommended to lower it a little. Generally, the value is between-0.3 and-1.0. 2. ** Rich and warm colors ** - Adding exposure compensation could make the photos look fresh, while lowering exposure compensation would make the photos look more intense. 3. ** Bleached Color ** - You can adjust the exposure compensation and white balance according to your personal style, and you can switch between light and dark. 4. ** Low Saturation Natural Tune ** - Adding exposure compensation could produce a fresh feeling, while lowering exposure compensation would produce a gentle tone. 5. ** Internet Celebrity Advanced Blue ** - You can adjust the exposure compensation and white balance according to your personal style. In addition, the image settings can be found in the menu (MENU)-(image settings). 6. ** Warm Colors ** - You can adjust the exposure compensation and white balance according to your personal style. When shooting portraits and skins, it is recommended that the exposure compensation is +0.7. 7. ** Black and White Film ** - According to the surrounding light, adjust the appropriate exposure compensation, and the 25600-degree exposure can create a strong black-and-white film effect. The exposure can be adjusted according to personal style. 8. ** Daily Film ** - You can adjust the exposure compensation and white balance according to your personal style. Increasing the exposure compensation can give you a refreshing feeling. In addition to the above parameters, the composition principle also had an important impact on the film: 1. In the case of non-special composition requirements, it is necessary to pay attention to the object in the photo to keep it vertical to the horizon, and the horizontal line to keep parallel to the horizon. 2. Other than the subject, try not to have other front or back scenes that attract the viewer's attention. For beginners, they could appreciate photography works on photography websites such as Netease photography, Hummingbird, Tugu, and China National Geography. They could learn to imitate the composition and reasonable exposure parameters in the works to improve the quality of the DSLR film. At the same time, he had to be clear about the effect he wanted, understand the meaning of the author's composition, the lighting environment, the angle of the light, and other factors. This would help to set the appropriate parameters during the shooting. In addition, in food photography, shooting angles such as 0 degrees (head-up), 45 degrees, 90 degrees (overlooking), etc. would also affect the effect of the film. Different angles had their own suitable scenes and composition matching methods. Read more exciting novels for free
Single lens reflex lens parameters
The angle of view of the medium focal length lens was between 40 degrees and 18 degrees, and the focal length range was between 61mm and 135 mm. The angle of view of a standard/medium-focus lens was about 40 - 55 degrees. In terms of optical characteristics, the photos taken at this focal length had the least distortion and could accurately reflect the shape of the subject. It was also relatively easy to design a large aperture. Different models of medium-focal lenses had different performance parameters in terms of distortion, dispersion, resolution, contrast, and so on. For example, the Olympus OM Zuiko auto-macro 90mm f/2.0 lens had an actual focal length of 90.44mm, an aperture of f/2.04, a pincushion-shaped distortion of 0.47%, and an edge loss of 0.3 stops at f/5.6. Minolta MC Rokkor -85mm f/1.7 lens, the actual test focal length was 85.6mm, with 0.5% barrel distortion, etc. <a href="/?from=ask_words" style="color:red" target="_blank">Read more exciting novels for free</a>
The parameters of a single-lens reflex camera
The following are some important settings for a DSLR camera: 1. ** Shooting Mode **: It is recommended to choose the manual mode (M). This way, you can control the shutter, aperture, sensitivity, and other parameters independently. 2. ** Video recording format and size **: If there are no special requirements, you can choose to record 1920*1080, 25 frames, MOV format of high-definition video. If there are special requirements for zooming in, you can choose 4K or other format. 3. ** Shutter Speed **: Generally, it is twice the frame rate of the video. For example, when the frame rate is 25 frames, the shutter speed is set to 50; when the frame rate is 60 frames, the shutter speed is set to 120. This way, the visual effect can be achieved. 4. ** Aperture **: The aperture size affects the depth of field of the picture. A large aperture (such as F2.8) made the picture brighter and the background blur stronger, while a small aperture (such as F11) made the picture darker and the background blur weaker. The larger the aperture value, the smaller the actual aperture. 5. ** Light sensitivity (USB)**: When there is sufficient light, the lower the USB, the better. It is not advisable to set it too high in a dark environment, otherwise it will produce noise. For example, Canon DSLR can be set to 100 during the day and 800 - 1000 at night. A high USB (greater than 2000) will produce obvious noise and it will be difficult to repair later. 6. ** Color temperature (white balance)**: adjust to manual mode. Generally, it is recommended to adjust the color temperature between 4900 and 5300. The higher the color temperature, the more yellow the screen will be, and the lower the color temperature, the more blue the screen will be. 7. ** Focus **: If you have good manual operation ability, you can try to manually focus and select the focus point. Novice or for convenience, you can use the automatic intelligent autofocus. However, it is recommended to practice manual focus more if possible. <a href="/?from=ask_words" style="color:red" target="_blank">Read more exciting novels for free</a>
After the parameters of single-lens reflex photography
Flash Shooting, Single-lens reflex, parameters
The following are some of the parameters of the DSLR camera when shooting with flash: ** 1. Night Portrait Shooting parameters ** - [Mode: Able to use Av (Aperture priority mode).] - [Light sensitivity: 100 - 400] - Aperture: around F8. - Flash mode: Use slow sync flash (the camera's default flash mode for night portrait mode. The flash flashes once when the shutter is pressed and again before the exposure ends). ** 2. The possible parameters of flash usage in different scenarios (comprehensive consideration)** - Shutter speed: The shutter speed will affect the brightness of the background. When using the flash, you also need to set it according to the needs of different scenes. For example, when shooting a baby/pet, the shutter speed should be above 1/200.(In the case of using the flash to supplement the light and need to take a photo, the high-speed shutter can freeze the instant action and avoid blurring due to hand shaking or pet movement.) - Aperture: Affects the brightness of the subject and the effect of blurring the background. For example, the aperture for indoor portrait shooting is below F2.8 (a large aperture can allow more light to enter the camera when there is insufficient light, and at the same time, it can blur the background and highlight the subject); the aperture for still life/food shooting is between F1.2 - 4; the aperture for night shooting is F10 or smaller (a small aperture can allow the depth of field to be larger, so that the entire night scene can be clearly captured). - Photosensitivity (USB): Affects the overall brightness. For example, for indoor portrait shooting, USB 1500 (indoor light is usually dim, so increasing USB can make the picture brighter, but too high USB may bring noise), while for baby/pet shooting, USB 100 - 800, still life/food shooting, USB 100 - 400, night shooting, USB 100 (Under the condition of ensuring sufficient exposure, try to use low USB to reduce noise). At the same time, he also needed to consider the white balance.(For example, the automatic white balance is the default setting of the camera. You can also customize the white balance according to the ambient light to ensure the accuracy of the color), Metering mode (There are evaluation, partial, spot, and center-focused average measurements. Different settings can be used to accurately expose different settings), exposure compensation (if you feel that the photo is too dark or too bright, you can further adjust the brightness of the photo), flash compensation (change the output intensity of the flash, usually used to adjust the brightness of the photo when filling up the light), and other parameters. <a href="/?from=ask_words" style="color:red" target="_blank">Read more exciting novels for free</a>
Take the parameters of the single-lens reflex camera
The following are some parameters that can be used as a reference when shooting car tracks: 1. ** Shutter Speed **: You can choose the shutter priority mode, and the shutter speed can be adjusted to 3 - 10 seconds. When shooting the tracks on the mountain road, due to the small number of vehicles, you can use Door B to manually control the shutter speed when you see the car to record the track of the car. You can also set the shutter speed to 3 - 30 seconds. The longer the exposure time, the more obvious the effect of the tracks. 2. ** Light sensitivity (USB)**: It is recommended to set it to 100 to reduce noise and ensure image quality. In the case of insufficient light, try not to exceed 6400. If it is too dark, consider using a fill light. 3. ** Aperture **: You can use automatic adjustment first. If you use the aperture priority mode for experimental photos, you can also refer to this setting if you choose f/8 aperture to achieve a suitable exposure combination. If you are taking a group photo with a similar scene, you can also set a small aperture of about f8 to ensure the picture is clear. In addition, a tripod, shutter release, and other equipment were needed to assist in the shooting. Under long exposure, noise reduction and lens anti-shake needed to be turned off for a long time. During the shooting process, a few more photos were taken to select satisfactory photos. Later, the color temperature was adjusted appropriately to achieve a satisfactory effect of the environment. <a href="/?from=ask_words" style="color:red" target="_blank">Read more exciting novels for free</a>
The parameters of a single-lens reflex camera in the studio
When shooting in the studio, the parameters of the single-lens reflex camera were set as follows: 1. ** Light sensitivity (USB)**: Due to the strong lighting in the studio, the sensitivity does not need to be too high. It can be set to a lower value, such as USB 50 or USB 100. 2. ** Metering method **: You can choose according to the subject. Matrix Metering is suitable for shooting natural scenery; Center Metering focuses on the central area of the picture, suitable for shooting portraits; Spot Metering focuses on the small area in the center of the picture. 3. ** Aperture and Shutter **: If you use the M mode, you need to set the aperture and shutter according to the light intensity in the studio and the light measurement results. You can also try taking a gray or white card, customize the white balance, check the highest sync speed of the flash, and then set the photo format. After the adjustment was completed, he could take a test shot. Then, he would connect the card to the computer and open the picture for comparison analysis and adjustment. If you use a constant light source to shoot still objects, it is recommended to use aperture priority and spot measurement. First, choose the depth of field according to the desired shooting effect, and then choose the aperture according to the depth of field. The camera will automatically match the shutter speed according to the ambient light. 4. ** White Balance **: If you use a constant light source, in order to accurately control the color temperature, it is recommended to use a gray card to correct the color temperature of the camera before taking a photo. 5. ** Lenses Setting **: Turn on surrounding brightness correction to reduce dark corners, turn on distortion correction, and select criteria for digital lens optimization. 6. ** Focus Mode **: You can set AF-ON to switch between single-shot focus, autofocus, and servo-autofocus. The setting step is to click AF-ON, then click the menu key (Menu). In the pop-up menu, choose the second camera setting from the right in the first layer of the menu. In the second layer of the menu, choose 3, and choose the custom button. Find AF-ON, which is the autofocus start button. 7. ** Image confirmation **: Generally, 2 seconds is enough. You can check the rough effect of the photo after the shooting. 8. ** High Iso-noise reduction setting **: If you are in an extremely dark environment without a lamp or tripod, you can set a high Iso-noise reduction setting to adjust the brightness of the screen. However, this method is not a long-term solution. If the environment is not bright enough, it is best to use lighting equipment. 9. ** Release the shutter without a memory card installed **: Choose to close the shutter to avoid accidentally pressing the shutter when the memory card is not installed. 10. ** Gridline Setting **: You can set it to 3x3 gridlines for easy composition. 11. ** exposure simulation **: When exposure simulation is enabled, what you see is what you get. The image you see on the screen is basically the same as the photo. <a href="/?from=ask_words" style="color:red" target="_blank">Read more exciting novels for free</a>
Save the parameters of the single-lens reflex photography
Different DSLR photography parameters were saved in different ways. The following are some common situations: - If you want to adjust the parameters such as the exposure time of the MasterAlignment camera, after adjusting the appropriate exposure time, click the "Save Setting" button. After confirming the save operation, the exposure time setting will take effect. After the adjustment is completed, you can close the camera parameters setting window. - For the Nikon D850 camera, after confirming that the 16:9 image ratio was selected, press the "OK" or "Enter" button to save the settings and adjust the camera to the 16:9 image ratio. In other single-lens reflex cameras, when adjusting parameters such as aperture, shutter speed, and white balance, you could usually find the corresponding save option in the camera's menu or save the adjusted parameters by pressing the confirm button. For example, if the camera had a special button or menu option to save the current settings or application settings after adjusting the sensitivity to an appropriate value, it could be saved by clicking it. <a href="/?from=ask_words" style="color:red" target="_blank">Read more exciting novels for free</a>
Single-lens reflex photography of flower parameters
When shooting flowers with a DSLR, you can refer to the following parameters: 1. ** Shooting Mode **: - Aperture priority exposure mode (Av mode) or M mode. - For close-up shots of flowers, the aperture priority mode can be set to the maximum or one to two degrees lower than the maximum (such as F2.8 or F3.5). - When shooting still life, flowers, fish, and insects (A), the aperture should be F5.6 or above and as large as possible. 2. ** Metering Mode **: Spot Metering. 3. ** Focus Mode **: - It can be set to single shot autofocus mode or autofocus (AF.) - When shooting close-ups of flowers, focus on the stamen to measure the light and focus. 4. ** Aperture **: - It depends on the effect you want to create. If you want a shallow depth of field effect (background blurring), you can set a larger aperture value, such as F2.8. If you want to shoot a large flower and need enough depth of field, you can reduce the aperture (increase the aperture value) appropriately, such as the aperture of 8 or above and 18 or below. However, you must pay attention to avoid the aperture being too small and causing noise to affect the image quality. 5. ** Light sensitivity (USB): - When the light was strong, the setting was set to 100, and when the light was weak, the setting should be within 400 and not exceed 800. - If you shoot in the studio, when the light is strong, the sensitivity should not be too high. You can lower the IQ. 6. ** White Balance **: Can be set to automatic white balance. 7. ** focal length **: Focus on telephoto, supplemented by other focal lengths. If the lens is pulled to the 55 telephoto end, the object can be shot closer to make the picture full. It can also be equipped with a macro lens (such as 100 micro) to shoot macro flowers. 8. ** Shooting Time **: - Usually, the light was soft from 6 to 10 in the morning, suitable for shooting. The lotus flowers and other flowers were blooming at this time. - Filmed in the afternoon before sunset, the spectrum was better, and the results were good. <a href="/?from=ask_words" style="color:red" target="_blank">Read more exciting novels for free</a>
Shooting indoor single-lens reflex parameters
The indoor DSLR shooting parameters were as follows: - Aperture: F1.2 - 4. - Shutter speed: 1/80s- 1/200s. - [Light sensitivity: 800 - 1500] <a href="/?from=ask_words" style="color:red" target="_blank">Read more exciting novels for free</a>
Single lens reflex camera parameters tutorial
The following is a tutorial on setting the parameters of the DSLR camera in different shooting scenes: ** 1. Portrait Shooting ** 1. ** Still Portrait ** - ** Shooting mode **: Aperture priority mode (LV) can be used. - ** Aperture Setting **: Use a large aperture, such as F2.8, to create a blurred background effect and highlight the main character. - ** Focus **: Focus on the eyes or key parts of the character. If you want to shoot a close-up of the character, the sharpness is moderate, and you can use the middle composition. When matching the character and the background, you can use the medium aperture F8 to highlight the character and the background. The focal length is the widest. The composition uses the three-point method or the golden section method. - ** Light sensitivity (USB)**: Try to set it as low as possible, such as USB 100. 2. ** When the character moves ** - ** Shooting Mode **: Shutter priority mode (TV). - ** Shutter Speed **: Usually set to about 1/250s to avoid blurring. ** 2. Scenery Shooting ** 1. ** Shooting Mode **: You can use P or M files. 2. ** Aperture setting **: Use a small aperture, generally F5.6 or smaller, such as F8 (on sunny days, around 100, F8, 1/200; on cloudy days, around 400). 3. ** Using the camera ** - ** Wide-angle lens **: It is suitable for taking photos of large scenes, such as buildings and landscapes. It has a short focal length, wide angle of view, and deep field of view, which can produce a strong visual impact. - Medium focus lens: It has the smallest distortion in the photo, can accurately reflect the shape of the subject, and is easy to design into a large aperture. - ** Telephoto lens **: Long focal length, small angle of view, large image on the film, suitable for shooting distant objects. 4. ** Composing **: To avoid placing the most attractive scenery in the middle, you can use the three-point composition, frame composition, symmetrical composition, diagonal composition, white space composition, etc. 5. ** Note **: It is recommended to bring a tripod to prevent the photo from blurring due to shaking. ** 3. Shoot flowers and plants ** 1. ** Shooting Mode **: Aperture priority mode (LV). 2. Aperture setting: Choose a large aperture lens or a 100-millimeter lens. The aperture should be large so that the depth of field is shallow and the subject can be highlighted. 3. ** Composing **: Use a central composition or a nine-square composition to place the object you want to shoot in the center of the picture. ** 4. Pet Shooting ** 1. ** Shooting Mode **: You can turn on the P automatic gear and start continuous shooting, or use the shutter priority mode (TV). 2. ** Shutter speed (in TV mode)**: Set it to 1/200s or higher. ** 5. Shooting Night Scenery ** 1. ** Shooting Mode **: Aperture priority mode or M mode can be used. 2. ** Aperture setting **: Use a small aperture, such as F10 or smaller. 3. ** Light sensitivity (USB)**: Normally set to USB 100. 4. ** Shutter Speed **: For example, 1/30s (Shutter 1/30, Aperture F10, SPD 100). 5. ** Metering Mode **: Can be set to the Evaluation Metering Mode (Matrix Metering Mode), and the exposure compensation can be reduced appropriately. 6. ** Ancestors **: Requires a tripod. If possible, you can use the shutter release to shoot. ** 6. Silhouette Shooting ** 1. ** Shooting Mode **: P-file is fine. 2. ** Metering **: Use spot photography to measure the highlight, then add or subtract the exposure according to actual needs, and place the focal point at the bright spot. ** 7. Setting the camera parameters for other shorthand scenes ** 1. ** Exterior Portrait **: 1/100s, Iso100, F1.2 - 2.8. 2. ** In-room portrait **: 1/80s, 1500, F2.8 or below. 3. ** Baby/Pet Shooting **: Above 1/200, USB 100 - 800, F1.4 - 5.6. 4. ** Still life/gourmet photography **: 1/80s- 1/200s, USB 100 - 400, F1.2 - 4. <a href="/?from=ask_words" style="color:red" target="_blank">Read more exciting novels for free</a>