The simplest handmade lantern
Here are a few relatively simple ways to make handmade lanterns: 1. ** Using Red Envelopes to Make Lanterns ** - Prepare some red packets, cut off the top seal, and use a utility knife to open three edges. Divide a complete red packet into two pieces, and take the back of the red packet and cut off about one centimeter wide. He took out the letter side of the red packet and drew a line with a pen (draw a one-centimeter-wide line on the left and right sides, and the inner part is equal to 0.5 mm). Then, he used a hand-made knife to cut open the thin line. He stuck double-sided tape on the one-centimeter-wide area on the left and right sides of the red packet's outer shell. He stuck the bottom of the letter side to the bottom surface of the red packet. He cut off a part of the left side and stuck double-sided tape on the bottom. Then, he used the cut edge to fold it and stick it to the top to complete a red lantern. 2. ** Using mineral water bottles to make lanterns ** - The plastic bottle was cut into strips at intervals of 1.5 centimeters. A tassel was pierced through the bottom of the bottle. A red balloon was placed at the mouth of the bottle and blown up. Finally, the bottle cap was closed. A rope was connected to the small wooden stick on the lid. The lantern was completed. 3. ** Using a piece of paper to make a lantern ** - He took a piece of paper and folded it up and down by 1cm. He cut the middle every 0.5cm. Then, he took the paper and stuck it on both sides of the paper. He cut two pieces of paper on one side and stuck them on the double-sided tape to roll them into a cylinder. He stuck them on the edge. Then, he took a long yellow paper and stuck them on for decoration. After crossing the short paper strips, he stuck them through the pendant and stuck them to the bottom of the lantern. Then, he stuck the handle. 4. ** Daddy's Paper Lantern Making (Simple Method Using Special Materials)** - Cut out a piece of transparent tape and paint it red. Use toothpicks to form four squares and paste the mooncake star decoration. Then stick a layer of transparent tape on it. Fold the edge and paste it. Treat the upper and lower parts in the same way and punch holes. If you don't have a pendant, you can make it yourself. Cut the rectangular paper into 0.5 cm thin strips, stick a red string and roll it up. Then stick the yellow paper decoration and pass it through the hole.
Handmade Antique Lantern
Here are a few ways to make handmade antique lanterns: ** 1. Use red paper to make ancient lanterns (Method 1)** 1. ** Material preparation **: Two A4-sized red cardboard, compasses, ruler, pencil, scissors, paper cutter, glue stick, drawing (you can choose ancient style pictures, if not, you can use patterned paper instead), ribbon, gold paper. 2. ** Production Steps ** - Take one of the red cardboard, draw a line two centimeters above and below, and divide it into five equal parts. Draw an arc above and below each grid, pay attention to leaving a place to paste, and then cut it along the line. Then, he drew another five millimeters in length, width, and depth in each of the two. - Cut another piece of red paper into ten circles, fold each circle three times towards the center of the circle, stand up the folded edges, cut off the small squares drawn with a paper cutter to get five boxes, and use the paper cutter to gently draw on the connecting line to facilitate folding. - He pasted the ten folded circles in groups of five in order (without sealing them). He cut the pattern that he had cut out earlier into the same size as a rectangular shape and pasted it on the square with its front facing down, forming a prism as the lantern body. - He stuck the assembled circles on the top and bottom of the lantern as the top and bottom. He cut the gold paper into tassels, rolled it on a thin ribbon to make the lantern tassel and put it through the lantern. Finally, he sealed the top and bottom, and tied the extra ribbon on the top and bottom as a hanging rope. ** 2. Use red paper to make ancient lanterns (Method 2)** 1. ** Material preparation **: Two A4-sized red cardboard, pencil, ruler, paper cutter, picture, ribbon, gold paper, glue stick, scissors, compasses. 2. ** Production Steps ** - Divide one of the red cardboard into ten equal parts, draw ten circles and cut them out. Cut out a part of the remaining paper from top to bottom (the length of the cut is the same as the radius of the circle). Divide the paper into five equal parts according to the diameter of the circle and draw a dividing line with a pencil and ruler. Draw five arcs from top to bottom (leave a place for the edge to be pasted) and cut them out. - He used a paper cutter to gently draw each fold line, fold the arc, cut the five pictures into suitable sizes, and pasted them on it. - Fold the circle into three arcs along the center point, and the ten sides form a triangle. After the ten circles are stacked like this, the fold line is erected. The five are stuck together in a group (do not seal) to form the top and bottom of the lantern. - He combined the top and bottom with the lantern body (do not seal the back cover), cut it into tassels with gold paper, roll the ribbon inside, pass the ribbon through the lantern body, tie a circle on the top for hanging, and finally seal the top and bottom. ** 3. Use long strips of cardboard to make ancient moon lanterns ** 1. [Material preparation: Long strip of cardboard.] 2. ** Production Steps ** - Divide the long cardboard into four parts, draw a circle in the middle of each part and hollow it out. Then stick the transparent tape on it, turn it to the sticky side and color it to get the shape of a round moon. - When the paper was connected end to end, it became the shape of a lantern. ** 4. Use black cardboard to make antique lanterns ** 1. ** Material preparation **: Black cardboard, patterned wrapping paper, white rubber, tassels, iron wire, transparent tape, electronic candle. 2. ** Production Steps ** - He cut the hexagonal patterned paper and the triangular cardboard. - Stick the cardboard on the flower paper, prepare 4 such combinations and connect them with tape. - After placing the electronic candle, he surrounded the cardboard and glued it together. Finally, he hung the tassel. ** 5. Use the gift box to make a traditional handmade lantern (hexagonal palace lantern)** 1. ** Material preparation **: Paper box (such as gift box), red cardboard, material paper, small paper strips, lamp (for the bottom), transparent sheet, plastic sheet, etc. 2. ** Production Steps ** - He cut open the lid of the paper box and cut out the six patterns to get the lantern frame. - The lantern was wrapped with red cardboard, and the cardboard was pasted with material paper and painted with patterns to thicken the base of the lantern. - He used small pieces of paper to form an antique door frame, added a light at the bottom, cut out a hexagon with a side length of 7 cm, and surrounded it with a transparent sheet. - He pasted the pattern of the gift box onto the plastic sheet and placed it into the lantern frame. Then, he cut a hollow hexagon to cover the lantern.
Handmade lantern making tutorial
The following are some handmade lantern making tutorial: ** 1. Use two pieces of A4 paper to make lanterns ** 1. He aligned the two pieces of A4 paper with the edges aligned. 2. He stuck one end of the paper together with the transparent tape, then stuck the bottom of the two pieces of paper together along the bottom edge. 3. Using the same method, he glued the other end of the paper to the side, forming a closed rectangular shape. 4. The four corners of the lantern were folded inwards to form an arc at the top, completing the shape of the lantern. ** Two, similar to how Dad made lanterns (using a variety of materials)** 1. He cut out a piece of transparent tape and painted it red. Then, he placed it in four squares with toothpicks and pasted the mooncake star decoration on it. 2. Then, he stuck a layer of transparent glue on top of it, folded it around the edges, and stuck it on top and bottom in the same way. 3. Punch holes up and down, cut the rectangular paper into 0.5 cm thin strips, stick a red string and roll it up, then stick a yellow paper decoration, and pass through the holes. 4. He folded the edges and stuck them together. He passed the hemp rope through the top and tied the tassels to the hemp rope. He placed them into the lamp and the ancient lantern was ready. ** 3. Making lanterns with mineral water bottles (example 1)** 1. Every 1.5 centimeters, he cut the plastic bottle into strips. 2. Thread a tassel at the bottom of the bottle, put a red balloon at the mouth of the bottle and blow it up. 3. He closed the bottle cap and tied a rope to the small wooden stick. ** 4. Making lanterns with mineral water bottles (example 2)** 1. He cut off a section of the mineral water bottle and pasted it on the yellow colored paper. 2. He made a small rabbit out of white paper, pasted it on the round moon, drew its facial features, and pasted it with small hands and clouds. 3. He punched a hole in the water bottle, passed it through a string on a mooncake box, and put in a small lamp. ** 5. Making lanterns with cardboard ** 1. Cut out 12 ladders of the same size (for the lantern body) and 2 hexagons (for the bottom and top). - Hexagon production steps: - Draw a straight line on the cardboard and determine the center point. - He used a protractor to find the 60-degree and 120-degree points and connected them to form a hexagonal prototype. - The length of the hexagon was taken as the size of the short side of the hexagon. 2. He hollowed out the middle of the 12 echelons and 2 hexagons (one of the hexagons should be used as the base to leave a place for candles). 3. Cover the hollowed out part of the lantern with cellophane (can be omitted). 4. He stuck the two long sides of the ladder together, and the short side of the ladder was stuck together with the hexagonal side. 5. The hexagon that made the roof was tied to the thread and glued to the echelon. ** 6. Create a lantern with Photoshop (PS software)** 1. He used the [Oval Tool] to draw an oval shape as the outline of the lantern. 2. Press [Control + J] to copy an oval shape, turn off the fill color, and choose yellow for the stroke. 3. Clone the yellow oval and press [Control + T] to shrink it. 4. Duplicated the yellow oval multiple times and shrunk it freely. 5. Using the [Rectangle Tool], he drew an orange and yellow rectangular shape and placed it above the lantern. 6. He copied a rectangular shape and placed it under the lantern. 7. He added the hanging rope and the tassel at the bottom of the lantern to complete the simple lantern production. ** 7. Make a simple lotus lantern (can be used as a lantern for the Mid-Autumn Festival)** 1. After folding the pink square paper several times, draw the arc of the petals on it, cut off the excess parts, and paste the glue on the short crease after opening it. 2. He took a paper cup, cut off the bottom, tied it with a string, and placed it in the middle of the petals. He folded the petals and stuck them to the cup. 3. He used green paper to make lotus leaves. After folding and opening them many times, he put them away along the traces. After folding and sticking them together, he made two lotus leaves and stuck them together. Then, he applied glue to the lotus leaves.
The simplest handmade flower basket teaching plan in kindergarten and reflection summary
"The simplest handmade flower basket lesson plan in kindergarten and reflection summary." ** 1. Teaching plan ** 1. ** Teaching goal ** - Let the child learn the simple skill of weaving a flower basket by hand. - Cultivate children's hands-on ability and creativity. - Arouse children's interest in manual activities. 2. ** Teaching Difficulties ** - ** Main point ** - Master the basic steps of weaving a flower basket. - ** Difficulty ** - How to make children neat and beautiful. 3. ** Teaching preparation ** - Prepare a sufficient number of colored paper strips (about 1 - 2 cm wide). - One small plastic ring for each child (it can be taken from waste). - Finished flower baskets for display. 4. ** Teaching process ** - ** import (3 minutes)** - The teacher walked into the classroom with a beautiful flower basket and asked the children,"Children, look at what the teacher is holding in his hand." Isn't it pretty?" Guide the child to observe the shape and color of the flower basket to stimulate the child's interest. - ** Explanation and demonstration (10 minutes)** - The teacher placed the prepared materials on the table and began to demonstrate the flower basket. - First of all, one end of the colored paper strip was fixed to the plastic ring. It could be glued or made into a knot. - Then, he began to weave the strips of paper around the plastic ring, like braids, one on top of the other. - When weaving, tell the child to weave it as tightly as possible so that the flower basket will be strong. - Demonstrate and explain at the same time, so that the child can clearly see every step. - ** Child operation (20 minutes)** - He distributed the materials to the children and asked them to weave the flower baskets themselves. - The teacher guided the children around the classroom and provided timely help to the children when they encountered difficulties. For example, if some children's notes were not fixed well, the teacher could help to fix them again; if some children were more messy, the teacher could remind them to make them in order. - ** Exhibition and evaluation of works (7 minutes)** - He asked the child to display the flower basket he had woven on the table. - The teacher evaluated the children's works, first praising each child's efforts and creativity, then picking out a few well-made works and pointing out their advantages, such as neat weaving, good color matching, etc. As for the works that weren't well-made, they also gave encouragement and told the children that they could do better next time. 5. ** Teaching Extension ** - After the children went home, they could use the same method to weave a bigger flower basket. They could also use their own flower baskets to store some small toys or snacks. ** 2. Reflection and conclusion ** 1. ** Success ** - The teaching goal was basically achieved. Most of the children had learned the basic skills of weaving flower baskets, and their hands-on ability had been trained. They also showed a high interest in weaving flower baskets. - The teaching method was more suitable. Through the demonstration and tour guidance, the child could clearly see the operation steps and receive timely help. The work display and evaluation segment also gave the children a sense of accomplishment and stimulated their self-confidence. 2. ** Inadequacies ** - He did not pay enough attention to the children who had poor hands-on skills. During the operation process of the children, although they were given itinerant guidance, there were still some children who did not weave a complete flower basket in the end. In the future, more individual guidance should be given to these children. - The materials could be more varied. Although colored paper strips and plastic rings could meet the basic teaching needs, if they could prepare some materials of different materials, such as hemp rope, wool, etc., the children could have more choices and the works would be more colorful. 3. ** Modification measures ** - For children with poor hands-on ability, some simple hand training activities, such as kneading plasticine, could be carried out before the activity to improve their hand flexibility. During the teaching process, this group of children should be given more time for individual guidance. - The next time he prepared the materials, he would collect materials of different materials to provide more creative space for the children. <a href="/?from=ask_words" style="color:red" target="_blank">Read more exciting novels for free</a>
Handmade and handmade e-book
handmade embroidery
Handmade embroidery was one of the best traditional China crafts, also known as silk embroidery. It had a history of at least two to three thousand years in China. It was a kind of embroidery that used silk thread to create various patterns. Handmade embroidery had a rich meaning. For example, a Miao girl went to various places to collect embroidery works in order to protect her own handmade embroidery. These embroidery products reflected tranquility, concentration, inheritance, and the continuation of national culture. In the place of the non-hereditary inheritor of Manxiu, there were qipaos embroidered by the embroidery lady, the painting of the Qingming Festival, and other embroidery works. The pictures were vivid and lifelike. In terms of types, there were different kinds of embroidery like Jiayu lace embroidery, such as three-dimensional embroidery, multi-colored flat embroidery, three-dimensional coiling embroidery, etc. There were many patterns. Just Jiayu lace embroidery had thousands of patterns in stock, and they could be customized to make dresses, children's dresses, halter dresses, etc. There were also embroidery pieces like Qing Dynasty's Qing Dynasty's Qing Dynasty. In terms of regional characteristics, due to different market demands and embroidery origins, embroidery crafts began to form their own local characteristics. Among them, embroidery products in Su, Shu, Yue, and Xiang had a wide market and great influence, forming the "Four Famous Embroideries". During the Ming and Qing Dynasties, folk handmade embroidery further developed, and Su embroidery, Yue embroidery, Xiang embroidery, and Shu embroidery developed. " Palace Wall Flower Shadow: The Legendary Life of the Mute Embroidery Girl " was equally exciting. Everyone was welcome to click and read it!
Transformers Handmade
Here are some of the ways to make Transformers by hand: - In terms of material preparation, he could use multiple packaging boxes, cardboard (used to make helmet arcs, etc.), LED lights (modified to make headlights), and other materials, just like when someone made Transformers for children. During production, for example, the middle could be hollowed out so that it could be worn on the body. If the upper body could not be worn after the upper body was made, the waist could be designed to open and close. The feet could be hollowed out and matched with shoes. It could also be used to make weapons for Transformers. - As for obtaining blueprints, he could search for the blueprints of the Transformers model on the Internet and then choose the ones he liked and which were simple to make. - He could also use the parts of the Transformers building blocks to modify them. For example, he could use the parts of the Bruko building blocks to make a mechanical flying wing. He would choose a building block with two round holes on the back (such as Prime, Megatron, etc.), install two universal joint keys, prepare the universal thigh parts, left and right hands, forearm and elbow joints, laser guns, special effects keys, etc. Finally, he would install the completed wings on the joint keys on the back. "Transformers: Origins" was not enough. Everyone, please click to read the novel!
Handmade airplane
There were many ways to make a handmade plane. It could be made with colored paper, such as in the book "Good Baby's creative colored paper handcraft: Hundred Paper Airplanes". There was also a method to make an airplane model with disposable chopsticks. First, collect enough chopsticks, wash and dry them, then cut them according to specific steps, stick them together, and assemble them. In addition, A4 paper could also be used to make a catapult paper plane. After a series of folding steps, such as folding left and right, overlapping the top corners, and so on, it could be launched after being stuck with a rubber band. There were also disposable paper cups that could be used to make toy planes, and even clay could be used to make planes (although they might not be able to fly). There was also a farmer from Shandong who had a junior high school education after the 1980s. He spent a lot of effort to make a real plane that could fly. The production process included deciphering the drawings provided by aviation enthusiasts and overcoming the difficulties of choosing materials. The novel "Hundred Years of Spaceship" is equally exciting. Everyone is welcome to click and read it!
Handmade Rocket
The following is a method to make a rocket by hand: 1. ** Material preparation ** - Choose an empty 1.5-liter soda bottle as the main body of the rocket. Make sure the bottle is clean and free of residue. - Prepare an air pump to inflate the rocket. - The cardboard was used to make the tail of the rocket. - The tape was used to fix the various parts. - Matches or lighters (used to ignite solid fuel). - Safety glasses to protect the eyes to ensure safety. 2. ** Production Steps ** - ** Prepare the rocket body **: The empty plastic bottle is the rocket body. - ** Making Tail Wing **: You can use three pieces of cardboard of the same width, one of which is slightly longer. He removed the middle part of the first piece of cardboard and turned it into a frame. He cut a strip from both sides of the second piece of cardboard and stuck the cut strip to both sides of the third piece of cardboard. Then, he stuck the first frame. Finally, he inserted the remaining second piece of cardboard and used two rubber bands to bounce them to both sides. Then, he decorated the rocket launcher. The rocket launcher was ready. He could also draw a few rockets and put them in the middle. He could pull them and launch them. 3. ** Propulsion system related (if involved)** - The propulsion system of a rocket usually consisted of fuel and an oxidiser. Self-made rockets could use solid fuel, such as gunpowder or a mixture of sugar and potash. It was important to note that self-made rockets were dangerous. Safety must be ensured during the operation and relevant safety regulations must be followed. The novel "Hundred Years of Spaceship" is equally exciting. Everyone is welcome to click and read it!
Handmade Bookmark
Here are a few ways to make a small signature by hand: ** 1. Leaf Vein Bookmark Creation Method ** 1. ** Choose leaves **: Choose leaves with thick and dense veins. Generally, it is suitable for evergreen trees, such as osmanthus leaves, heather leaves, papaya leaves, oak leaves, tea leaves, etc. The leaves were selected in late summer or autumn when the leaves were fully mature and began to age. 2. ** Boiling the leaves with soda solution **: Based on 1 liter of water, prepare 70 grams of soda and 50 grams of soda (these two drugs are available in chemical stores). Limewater can also be used instead of soda solution. In an porcelain cup or casserole, boil the prepared soda solution and put in an appropriate amount of washed leaves. After boiling, gently stir the leaves with chopsticks to prevent stacking, so that they are evenly heated. Boil for about 5 minutes. After the leaves turn black, scoop out a leaf and put it into a plastic basin filled with clear water. Check if the meshy flesh is corroded and easy to peel off. If it is easy to separate, fish out all the leaves and put them into a plastic basin filled with clear water. Then, separate the meshy flesh from the leaf veins one by one. 3. ** Remove the meshy flesh **: Place the boiled leaves on your palm or on a glass plate. Gently wipe the surface of the leaves with the smooth part of the old toothbrush handle. The corroded meshy flesh can be wiped off. Then rinse it under the tap and continue to wipe until the meshy flesh is completely removed. 4. [Bleached Leaf Veins]: Put the cleaned leaf veins in a solution of bleachers, rinse them with clean water, and put them in old books and newspapers. After absorbing the water, take them out and use them as leaf bookmark. 5. Dyeing, Drawing, Writing: You can use red, blue ink or other dyeing agents to dye your favorite color. You can also draw, write, and finally tie a thread on it. ** 2. How to paste a bookmark ** 1. [Material preparation: Flowers such as peach blossoms and winter jasmines, or small animals such as butterflies and moths; scotch tape, tweezers, ribbons, cardboard, and old newspapers.] 2. ** Production steps **: Carefully tear off the petals, stamens, or wings and antennae of the butterfly with tweezers, place them on a piece of hard paper, arrange them according to your own design, and stretch the petals or wings. They were fixed to a piece of paper with transparent tape, covered with a few layers of old newspaper, and then added glass, dehydrated and pressed dry. After the water dried, cut the cardboard into a heart shape, triangle shape, fan shape, etc., and finally tie a ribbon to make a beautiful sticker bookmark. ** 3. How to make a photo bookmark ** 1. ** Material preparation **: ginkgo leaves, branches of Metasequoia glyptostroboides, clustered plants or small animals such as longicorn beetles and locusts; printing paper, developer, fixer, transparent tape, ribbons, and transparent glue. 2. ** Production steps **: Take a piece of transparent film and cut it into a rectangular shape slightly longer than the bookmark. The dried plant leaves and branches were trimmed and arranged on the film, and then fixed with thin strips of transparent tape. For moths and butterflies, only their wings were taken, and after being pieced together, they were glued together with tape. It was best to remove the internal organs of small animals such as locusts with a syringe and then fix them on the film. In the dark room (with the red light turned on), cut out the No. 2 or No. 3 printing paper of the same size as the film, put the film with the specimen on the printing paper, and press it with a clean glass sheet. Carefully expose it to light for about 10 seconds (the light intensity will shorten the time), then immediately turn off the light and put the printing paper into the developer. After a clear image appeared on the photo paper, it was placed in the fixer for 10 minutes. After that, it was rinsed with water, dried, trimmed, and finally colored with transparent watercolor. After tying a ribbon, it was made into a bookmark with animal and plant images printed on it. ** 4. Use hard shell or thin cardboard to make a bookmark ** 1. [Material preparation: Solid glue, scissors, colored Xuan paper, tassels, a hole cutter, some hard-shell flyers from some merchants, a support plate for clothes, and a trademark card.] 2. ** Production Steps **: - Use a knife to cut the hard shell or thin cardboard to the size of the bookmark you want (small bookmark looks better). - Cut the colored paper into the size of a bookmark and stick it on the cardboard. If the back doesn't look good, wrap it all with colored paper. - Punch holes and wear tassels. - Bookmarks could be written with inspirational sayings, stamped with decorative seals, or they could be left bare. "Luo Mingxia Love Letter" is equally exciting. Everyone is welcome to click and read it!
Handmade album
There were many ways to make a handmade photo album. The first method was Super Happiness's handmade photo album. It required four ice cream sticks, a hemp rope, six small beads, a photo album, and a pair of scissors. First, he crossed the top of the two ice cream sticks in pairs. After fixing them with hemp rope, he removed the excess thread and tied them up. He reserved a section of hemp rope for the colored beads. After the colored beads were put on, he used the remaining rope to fix the last right angle. Then, he placed the family photo and adjusted the ratio of the photo frame appropriately. Another way was to first choose the photos you liked and import them into the computer to print them out. The printed photos were cold-mounted to prevent color change and fading. Then, they were fixed to the inner pages of the album with tape. Finally, they were decorated with diamond-like or lace-like paste according to their preferences. Handmade photo albums could be creative. They could use various materials such as colored paper, sticker, clip art, etc. to create a unique photo album. This method was interesting and could allow people to enjoy the creation process. The novel " Watching the Moon on Fish Island " is equally exciting. Everyone is welcome to click and read it!