Handmade airplane
There were many ways to make a handmade plane. It could be made with colored paper, such as in the book "Good Baby's creative colored paper handcraft: Hundred Paper Airplanes". There was also a method to make an airplane model with disposable chopsticks. First, collect enough chopsticks, wash and dry them, then cut them according to specific steps, stick them together, and assemble them. In addition, A4 paper could also be used to make a catapult paper plane. After a series of folding steps, such as folding left and right, overlapping the top corners, and so on, it could be launched after being stuck with a rubber band. There were also disposable paper cups that could be used to make toy planes, and even clay could be used to make planes (although they might not be able to fly). There was also a farmer from Shandong who had a junior high school education after the 1980s. He spent a lot of effort to make a real plane that could fly. The production process included deciphering the drawings provided by aviation enthusiasts and overcoming the difficulties of choosing materials. The novel "Hundred Years of Spaceship" is equally exciting. Everyone is welcome to click and read it!
National Day handmade paper airplane
The following are some of the handmade methods of the National Day paper airplane: 1. [Material preparation: Square paper or rectangular paper.] 2. ** Basic folding method example 1 ** - First, he folded the square paper in half to form a cross crease. Then, he folded it diagonally to form a cross crease. - The four corners were folded towards the center, the two sides were folded towards the center line, then folded back, and then folded again. - The same folding method was used to fold a total of four pieces. Cut a knife at a 1cm spot, cut another 1cm, fold it in half, and then fold it on both sides to complete the tail of the aircraft. - He turned it over and folded it in half. - He combined the four parts, inserted one small corner into the corresponding position, and the other small corner was also inserted and fixed. The other two parts were operated similarly. - Finally, he assembled the tail of the plane and inserted the two small corners into the gap. He could also use an imprinting device to press out two five-pointed stars and glue them to both sides. 3. ** Basic folding method example 2 ** - Divide the square paper into four parts, fold the four corners in the middle, fold a sharp point, fold it back, and fold it in half. - [Making the Tail (Part 1): Fold out 4 parts, cut off the corners, and fold them together.] - [Spare Part 2 and Spare Part 3 (Wings): Fold 2 corners to make 2 wings.] - He began to assemble the plane. He inserted the wings into the slots and then the tail. He could add a five-pointed star decoration. The novel "Hundred Years of Spaceship" is equally exciting. Everyone is welcome to click and read it!
Handmade airplane model for primary school students
The following are some methods suitable for primary school students to make handmade airplane models: ** 1. Method of making disposable chopstick airplane model ** 1. ** Material preparation ** - A pair of chopsticks, a bamboo skewer, scissors, 502 glue, a utility knife, 80#and 240#sandpaper. 2. ** Production Steps ** - He first stuck the seven chopsticks together, then shaved one end, rounded it, and cut it into a shape of about 45° (the angle did not have to be too precise). Then, he arranged them one by one. He made two of these parts in the same way. After that, he used 80#sandpaper to polish the two parts so that their angles were the same as much as possible. Then, he used 240#sandpaper to further polish them to make them smoother. Then, he made three similar parts at about 45 degrees, stuck a chopstick on one of them, and then glued all the parts together. After that, he made a base plate and chopsticks to support it. After that, he stuck a bamboo stick on the tail, and the plane model was completed. ** 2. Other general ideas for making simple handmade airplane models ** 1. ** Understanding the basic structure ** - An airplane model usually had a body, wings, tail, and other parts. The main body of the plane was the body that connected the other parts. The wings could provide lift, allowing the plane to fly in the air. Its shape and size would affect the flight performance of the plane. The tail consists of a horizontal tail and a vertical tail. The horizontal tail helps to control the pitch of the aircraft (raising and lowering), while the vertical tail controls the direction of the aircraft (turning left and right). 2. ** Materials and Tools ** - The materials could be easily obtained paper (such as A4 paper), light wood, foam board, etc. In terms of tools, scissors were necessary for cutting materials; if light wood chips or foam boards were used, a utility knife might be needed for more precise cutting; glue (such as white rubber, hot melt glue, etc.) was used to stick parts; in addition, a pencil and ruler could be used to draw sketches and measure size. 3. ** Production process example (paper airplane model as an example)** - First, use A4 paper to make the body. He placed the paper vertically, starting from one end of the paper, and folded it up a small section to form the head of the plane. Then, he rolled the paper down along the long side of the paper to a suitable width, and folded the rest of the paper toward the body of the plane to form the tail of the plane. Next, he made the wings. He cut out two identical ladders from another piece of paper. The long side of the ladder was the leading edge of the wing, and the short side was the trailing edge. He stuck the wings to a suitable position on the body, usually at the back of the middle of the body. Finally, he made the tail. He cut out a small horizontal tail and a vertical tail and pasted them on the tail of the body. When making handmade aircraft models, primary school students should pay attention to safety. For example, when using scissors and utility knives, they should be careful to avoid injury. If glue is used, it should also be prevented from getting the glue on the eyes or skin. The novel "Hundred Years of Spaceship" is equally exciting. Everyone is welcome to click and read it!
Handmade and handmade e-book
handmade embroidery
Handmade embroidery was one of the best traditional China crafts, also known as silk embroidery. It had a history of at least two to three thousand years in China. It was a kind of embroidery that used silk thread to create various patterns. Handmade embroidery had a rich meaning. For example, a Miao girl went to various places to collect embroidery works in order to protect her own handmade embroidery. These embroidery products reflected tranquility, concentration, inheritance, and the continuation of national culture. In the place of the non-hereditary inheritor of Manxiu, there were qipaos embroidered by the embroidery lady, the painting of the Qingming Festival, and other embroidery works. The pictures were vivid and lifelike. In terms of types, there were different kinds of embroidery like Jiayu lace embroidery, such as three-dimensional embroidery, multi-colored flat embroidery, three-dimensional coiling embroidery, etc. There were many patterns. Just Jiayu lace embroidery had thousands of patterns in stock, and they could be customized to make dresses, children's dresses, halter dresses, etc. There were also embroidery pieces like Qing Dynasty's Qing Dynasty's Qing Dynasty. In terms of regional characteristics, due to different market demands and embroidery origins, embroidery crafts began to form their own local characteristics. Among them, embroidery products in Su, Shu, Yue, and Xiang had a wide market and great influence, forming the "Four Famous Embroideries". During the Ming and Qing Dynasties, folk handmade embroidery further developed, and Su embroidery, Yue embroidery, Xiang embroidery, and Shu embroidery developed. " Palace Wall Flower Shadow: The Legendary Life of the Mute Embroidery Girl " was equally exciting. Everyone was welcome to click and read it!
Transformers Handmade
Here are some of the ways to make Transformers by hand: - In terms of material preparation, he could use multiple packaging boxes, cardboard (used to make helmet arcs, etc.), LED lights (modified to make headlights), and other materials, just like when someone made Transformers for children. During production, for example, the middle could be hollowed out so that it could be worn on the body. If the upper body could not be worn after the upper body was made, the waist could be designed to open and close. The feet could be hollowed out and matched with shoes. It could also be used to make weapons for Transformers. - As for obtaining blueprints, he could search for the blueprints of the Transformers model on the Internet and then choose the ones he liked and which were simple to make. - He could also use the parts of the Transformers building blocks to modify them. For example, he could use the parts of the Bruko building blocks to make a mechanical flying wing. He would choose a building block with two round holes on the back (such as Prime, Megatron, etc.), install two universal joint keys, prepare the universal thigh parts, left and right hands, forearm and elbow joints, laser guns, special effects keys, etc. Finally, he would install the completed wings on the joint keys on the back. "Transformers: Origins" was not enough. Everyone, please click to read the novel!
Handmade Rocket
The following is a method to make a rocket by hand: 1. ** Material preparation ** - Choose an empty 1.5-liter soda bottle as the main body of the rocket. Make sure the bottle is clean and free of residue. - Prepare an air pump to inflate the rocket. - The cardboard was used to make the tail of the rocket. - The tape was used to fix the various parts. - Matches or lighters (used to ignite solid fuel). - Safety glasses to protect the eyes to ensure safety. 2. ** Production Steps ** - ** Prepare the rocket body **: The empty plastic bottle is the rocket body. - ** Making Tail Wing **: You can use three pieces of cardboard of the same width, one of which is slightly longer. He removed the middle part of the first piece of cardboard and turned it into a frame. He cut a strip from both sides of the second piece of cardboard and stuck the cut strip to both sides of the third piece of cardboard. Then, he stuck the first frame. Finally, he inserted the remaining second piece of cardboard and used two rubber bands to bounce them to both sides. Then, he decorated the rocket launcher. The rocket launcher was ready. He could also draw a few rockets and put them in the middle. He could pull them and launch them. 3. ** Propulsion system related (if involved)** - The propulsion system of a rocket usually consisted of fuel and an oxidiser. Self-made rockets could use solid fuel, such as gunpowder or a mixture of sugar and potash. It was important to note that self-made rockets were dangerous. Safety must be ensured during the operation and relevant safety regulations must be followed. The novel "Hundred Years of Spaceship" is equally exciting. Everyone is welcome to click and read it!
Handmade Bookmark
Here are a few ways to make a small signature by hand: ** 1. Leaf Vein Bookmark Creation Method ** 1. ** Choose leaves **: Choose leaves with thick and dense veins. Generally, it is suitable for evergreen trees, such as osmanthus leaves, heather leaves, papaya leaves, oak leaves, tea leaves, etc. The leaves were selected in late summer or autumn when the leaves were fully mature and began to age. 2. ** Boiling the leaves with soda solution **: Based on 1 liter of water, prepare 70 grams of soda and 50 grams of soda (these two drugs are available in chemical stores). Limewater can also be used instead of soda solution. In an porcelain cup or casserole, boil the prepared soda solution and put in an appropriate amount of washed leaves. After boiling, gently stir the leaves with chopsticks to prevent stacking, so that they are evenly heated. Boil for about 5 minutes. After the leaves turn black, scoop out a leaf and put it into a plastic basin filled with clear water. Check if the meshy flesh is corroded and easy to peel off. If it is easy to separate, fish out all the leaves and put them into a plastic basin filled with clear water. Then, separate the meshy flesh from the leaf veins one by one. 3. ** Remove the meshy flesh **: Place the boiled leaves on your palm or on a glass plate. Gently wipe the surface of the leaves with the smooth part of the old toothbrush handle. The corroded meshy flesh can be wiped off. Then rinse it under the tap and continue to wipe until the meshy flesh is completely removed. 4. [Bleached Leaf Veins]: Put the cleaned leaf veins in a solution of bleachers, rinse them with clean water, and put them in old books and newspapers. After absorbing the water, take them out and use them as leaf bookmark. 5. Dyeing, Drawing, Writing: You can use red, blue ink or other dyeing agents to dye your favorite color. You can also draw, write, and finally tie a thread on it. ** 2. How to paste a bookmark ** 1. [Material preparation: Flowers such as peach blossoms and winter jasmines, or small animals such as butterflies and moths; scotch tape, tweezers, ribbons, cardboard, and old newspapers.] 2. ** Production steps **: Carefully tear off the petals, stamens, or wings and antennae of the butterfly with tweezers, place them on a piece of hard paper, arrange them according to your own design, and stretch the petals or wings. They were fixed to a piece of paper with transparent tape, covered with a few layers of old newspaper, and then added glass, dehydrated and pressed dry. After the water dried, cut the cardboard into a heart shape, triangle shape, fan shape, etc., and finally tie a ribbon to make a beautiful sticker bookmark. ** 3. How to make a photo bookmark ** 1. ** Material preparation **: ginkgo leaves, branches of Metasequoia glyptostroboides, clustered plants or small animals such as longicorn beetles and locusts; printing paper, developer, fixer, transparent tape, ribbons, and transparent glue. 2. ** Production steps **: Take a piece of transparent film and cut it into a rectangular shape slightly longer than the bookmark. The dried plant leaves and branches were trimmed and arranged on the film, and then fixed with thin strips of transparent tape. For moths and butterflies, only their wings were taken, and after being pieced together, they were glued together with tape. It was best to remove the internal organs of small animals such as locusts with a syringe and then fix them on the film. In the dark room (with the red light turned on), cut out the No. 2 or No. 3 printing paper of the same size as the film, put the film with the specimen on the printing paper, and press it with a clean glass sheet. Carefully expose it to light for about 10 seconds (the light intensity will shorten the time), then immediately turn off the light and put the printing paper into the developer. After a clear image appeared on the photo paper, it was placed in the fixer for 10 minutes. After that, it was rinsed with water, dried, trimmed, and finally colored with transparent watercolor. After tying a ribbon, it was made into a bookmark with animal and plant images printed on it. ** 4. Use hard shell or thin cardboard to make a bookmark ** 1. [Material preparation: Solid glue, scissors, colored Xuan paper, tassels, a hole cutter, some hard-shell flyers from some merchants, a support plate for clothes, and a trademark card.] 2. ** Production Steps **: - Use a knife to cut the hard shell or thin cardboard to the size of the bookmark you want (small bookmark looks better). - Cut the colored paper into the size of a bookmark and stick it on the cardboard. If the back doesn't look good, wrap it all with colored paper. - Punch holes and wear tassels. - Bookmarks could be written with inspirational sayings, stamped with decorative seals, or they could be left bare. "Luo Mingxia Love Letter" is equally exciting. Everyone is welcome to click and read it!
Handmade album
There were many ways to make a handmade photo album. The first method was Super Happiness's handmade photo album. It required four ice cream sticks, a hemp rope, six small beads, a photo album, and a pair of scissors. First, he crossed the top of the two ice cream sticks in pairs. After fixing them with hemp rope, he removed the excess thread and tied them up. He reserved a section of hemp rope for the colored beads. After the colored beads were put on, he used the remaining rope to fix the last right angle. Then, he placed the family photo and adjusted the ratio of the photo frame appropriately. Another way was to first choose the photos you liked and import them into the computer to print them out. The printed photos were cold-mounted to prevent color change and fading. Then, they were fixed to the inner pages of the album with tape. Finally, they were decorated with diamond-like or lace-like paste according to their preferences. Handmade photo albums could be creative. They could use various materials such as colored paper, sticker, clip art, etc. to create a unique photo album. This method was interesting and could allow people to enjoy the creation process. The novel " Watching the Moon on Fish Island " is equally exciting. Everyone is welcome to click and read it!
Handmade curtain
Here are some ways to make a handmade curtain: - ** Curtain made of scrap cloth **: - He cut out a piece of cloth that was about four centimeters larger than the door from the discarded cloth. - Fold the cloth about 2 cm at one end and sew it properly. - A piece of PVP tube was passed through the sewn part. - He fixed the end of the string with the PVP pipe to the top of the door. - You can sew lace on the curtain. - Paper clip curtain (summer curtain): Cut the paper into small strips, add a layer of popsicle bag (plastic) on the outside, roll it on the paper clip, and then string the paper clips together to make the curtain. - Butterfly Curtain (fluorescent butterfly curtain): - Prepare materials such as a three-dimensional butterfly, three bottles of paint, glue sticks, 10 x 10 cm cardboard, a bundle of fishing line, a brush, 20 to 30 pieces of paper, a pencil, an eraser, and so on. - First, he folded the paper in half, folded the butterfly in half, and placed it on the cardboard. Then, he used a pencil to draw the shape of the butterfly (if he could draw it directly, he could skip it), and then cut out more than 20 of them. - He painted the paint and painted the texture from the middle to the outside, then dried it for about half an hour. - Use hot-melt glue to fix the position at five points on the windowsill or door and connect the fishing line, leaving the length slightly longer. - After applying hot melt glue on the back of the dried butterfly, he stuck it on the fishing line and arranged it according to his preference. - ** Crystal Furry Curtain **: Made of furry balls and crystals. The specific steps are not mentioned in detail, but it is easy to learn and inherited the craftsmanship. - ** Weaving rope curtain **: Can imitate 30 types of macrame rope curtain curtain works to make. While waiting for the TV series, he could also read the exciting content related to this site!
Handmade cartoon
The cartoon figure was a small figure made of a character or character in a cute and exaggerated style. For example, Art Museum of Horror released a cartoon figure of the main character, which was inspired by the interior of the art gallery in the game. In Honor of Kings, if you bought the Mirror Rose Detective skin, you could get a cartoon coupon. There was also a cartoon figure based on Jojo's character. In addition, the Q version of the figurine could also be made in some creative ways, such as the Q version of the figurine that someone used clay to pinch the head of the strange thief Kidd's fan, and the Green Alliance Q Pai robot fast charging charger that incorporated expression elements into the design. The Q version looked like a robot and could be used as a desktop decoration with a charging function. While waiting for the anime, you can also click on the link below to read the classic original work of " Full-time Expert "!