Single-phase double-capacity motor starts, doesn't turn, hums
The single-phase double-capacity motor starts and does not turn but hums due to the following reasons: 1. ** Mechanical Failure ** - There may be a stuck condition in the motor's rotor. It is necessary to check whether the motor's rotor.is stuck by foreign objects or the bearing is damaged. This could be determined by manually rotating the motor's motor. If the motor's rotation was not flexible or even unable to rotate, this could be the problem. - Obvious damage or distortion of the motor shell may also affect the normal operation of the motor. In this case, the relative position of the internal parts of the motor may change, resulting in a malfunction. 2. ** In terms of electrical faults ** - Condenser problem: - Failure of the starting capacity: The damaged or reduced capacity of the starting capacity will cause the motor to be unable to obtain enough phase difference to form a rotating magnetic field to start the motor. Although the appearance of the electric current seemed normal, it might have been damaged internally. You could use a universal meter to check if the capacity of the electric current was within the normal range. - Failure of the running capacity: If there is a problem with the running capacity, it may also affect the normal operation of the motor after starting, causing the starting to fail and make a buzzing sound. - Winding problem: The starting winding or running winding of the motor may have short circuit or open circuit phenomenon. Use a Multimeter to measure the resistance value of the winding. If the resistance value is not within the normal range (for example, the deviation is large compared to the standard resistance value when the motor is working normally, or the measurement shows infinity, indicating a break), it means that there is a problem with the winding. - Connection problem: The connection of the terminal in the motor terminal box may be wrong or loose or fall off, which will affect the normal flow of current through the motor winding, thus preventing the motor from starting normally. If the specific cause of the fault cannot be determined after inspection or there is insufficient maintenance skills, it is recommended to contact a professional motor maintenance personnel for maintenance. Read more exciting novels for free
The single-phase motor hums and doesn't rotate. The capacity is good.
If the single-phase motor does not buzz and the capacity is good, it may be caused by the following reasons: 1. ** Power supply problem ** - Unstable power supply or insufficient voltage will make the motor unable to work properly. Check whether the power circuit is normal, the voltage is stable, and whether the fuse is blown. 2. ** Internal problem of the motor ** - Stator coil short-circuit, open circuit of the motor and other problems will affect the normal operation of the motor. For example, the internal head end of the stators is connected wrongly, or there is a break or short circuit. At this time, the head and tail ends of the three phases need to be re-determined, and the three-phase winding should be checked for any break or short circuit. If the open circuit of the wound motor is broken, the connection of the brushes, slip rings and starting resistance contactors should be checked. 3. ** External motor problem ** - The motor bearings were worn out and the motor hub was loose, which would cause the motor to not work properly. 4. ** Other possible reasons ** - When the carrying capacity of the motor was overloaded, the motor could be unloaded and then started with no load or half load. If the dragged machine was stuck, it was estimated that it was due to the fault of the dragged machine. Unload the dragged machine and find the fault from the dragged machine. The motor could not work normally due to the imbalance of the motor's motor. <a href="/?from=ask_words" style="color:red" target="_blank">Read more exciting novels for free</a>
Single-phase 6-wire single-capacity motor
Single-phase 6-wire single-capacity motor, in which 6 wires contain 3 coil, can connect one end of the 3 coil together, the remaining 3 wires, one is connected to the live wire, one is connected to the capacity, and one is connected to the neutral wire. Of the six leads, two were for the main coil, two were for the auxiliary coil, and two were for the centrifugal switch. The three parts, namely, the transformer, the centrifugal switch, and the starting coil, had to be connected in series to form a circuit, which was connected in parallel with the main coil to supply power. If the direction was wrong, the two ends of the main coil could be reversed. <a href="/?from=ask_words" style="color:red" target="_blank">Read more exciting novels for free</a>
Single-phase 15,000 W motor with a large capacity
For the choice of 15kW-single-phase motor, the first thing to do was to determine the type of the motor. Generally, the choice could be an Electrolyte or Metal Film Condenser, which was suitable for high-power single-phase motor. Then, through the formula,(C = I / (2 Pi f Delta V)/), where/(C/) represents the size of the capacity.(Unit is Farad [F]),[I] represents the current when the motor is running (Unit is Ampere [A]). According to experience, 1,000,000 volts is about 6A, and 15,000,000 volts is about [15×6 = 90A].[F] represents the frequency of the power supply (Unit is Hertz [Hertz]), and [Delta V] represents the difference between the rated voltage of the voltage and the power supply voltage (Unit is Volts [V]). At the same time, for the 1. 5kW-single-phase motor, the operating capacity should be 45 - 60uF, and the starting capacity should be 100 - 250uF times of the operating capacity. According to experience, the operating capacity of the 1kW-single-phase motor should be 30 - 40uF, and the starting capacity should be 2 - 4 times of the operating capacity. It can be used as a reference for the selection of the 15kW-single-phase motor. In addition, the voltage endurance value of the capacity is greater than or equal to 1.5 times the power supply voltage. Generally, 400V/450V is selected. <a href="/?from=ask_words" style="color:red" target="_blank">Read more exciting novels for free</a>
Single-phase running capacity induction motor
Single-phase induction motor is a type of single-phase induction motor. In this kind of motor, the auxiliary winding and the working transformer connected in series with it were always connected to the power supply and participated in the operation of the motor, regardless of whether it was the starting process or the operation process of the motor. During the design, the main consideration was that the motor should have the best power index in the rated operating state, which would weaken the starting performance requirements of the motor, so the starting moment was relatively low. Its power range can range from a few volts to a few hundred volts, for example, there are products with different power levels such as 0.55kw and 120W. It is suitable for electrical appliances, special compression pump and small machine tools that require high performance. <a href="/?from=ask_words" style="color:red" target="_blank">Read more exciting novels for free</a>
Single-phase motor how to match the formula of the capacity
There are several formulas for the matching of single-phase motor with the following: 1. Calculating the working capacity according to the power: \(GC = 1950I/U\cos_\)(microfarad),\(I_) is the motor current,\(U_) is the single-phase power supply voltage, and\(\cos_\) is the power factor (take\(0.75_)). If the single-phase power is taken as\(220Vdm_), then\(GC = 1950P/(U ^2)\cos_= 1950*P/(220*220)*0.75 = 0.03*P(uF), and\(P_) is the motor power. After calculating the working capacity, the starting capacity shall be taken as 1 - 4 times of the working capacity. 2. <<C = 2 <fL>/<^2>>, where <C> is the capacity of the transformer,<f> is the frequency of the power supply,<L> is the induction of the motor, and <<^2>> is the power factor. 3. When the transformer is damaged and the labeled parameters are unknown, it can be selected according to the calculation of C = 8fs (uF), where C is the matching capacity (unit is microfarad); J is the current density of the motor starting winding (generally choose 5 - 7A/square); s is the cross-section area of the starting winding wire (square). <a href="/?from=ask_words" style="color:red" target="_blank">Read more exciting novels for free</a>
Method for connecting single-phase motor to starting capacity
The following are some ways to connect a single-phase motor to the starting capacity: 1. ** Connection according to resistance value **: connect the two wires with the largest resistance value to the voltage, and connect the two wires with the smallest resistance value to the power supply. For example, the red and yellow wires were connected to the electric capacity, and the red and blue wires were connected to the power supply (the red and blue and yellow and blue winding values were not equal, and the motor could not be used for positive and negative rotation). 2. ** Connecting according to the letter of the binding post **: The letters U1 and U2 of the binding post are connected to the two outgoing lines of the running winding, V1 and V2 are connected to the two outgoing lines of the centrifugal switch, W1 and W2 are connected to the two outgoing lines of the starting winding, and the starting capacity is connected to W1 and V2. After connecting U1 and W2 with the connecting piece, connect them to a power cord. After connecting V1 and U2 with the connecting piece, connect them to another power cord. 3. ** For the double-value capacity motor **: The double-value capacity induction motor has a starting capacity and a running capacity. The two capacity are connected in parallel and then connected to the starting winding. 4. ** Consider the positive and negative connection **: The starting capacity is connected in parallel to the main winding and the secondary winding (the two wires with the largest resistance value among the three wires). One of the two wires is connected to the power supply line, and the common end is connected to the power supply neutral line. If this rotation is recorded as positive rotation, then when the line is connected to the other wire of the starting capacity, it is reversed. <a href="/?from=ask_words" style="color:red" target="_blank">Read more exciting novels for free</a>
How to connect the single capacity of a two-phase motor
Two-phase motor single-capacity four-wire connection method is as follows: 1. The main coil of the two-phase motor was connected to L1 and L2 of the power supply. 2. The auxiliary coil of the two-phase motor was connected to L1 of the power supply. 3. One end of the transformer was connected to L2 of the power supply, and the other end was connected to the auxiliary coil of the two-phase motor. 4. A starting reactor is connected between the main coil and the auxiliary coil of the two-phase motor. 5. Ground the casing of the two-phase motor. <a href="/?from=ask_words" style="color:red" target="_blank">Read more exciting novels for free</a>
single-phase motor single-capacity reversing switch connection method
For the single-phase motor single-capacity reversing switch connection, it must first be clear that the single-phase motor has a main winding and a secondary winding, and there is a starting capacity between the secondary winding and the main winding. Generally speaking, the resistance value between the three wires of the single-phase motor was measured with a Multimeter. The two wires with the largest resistance were connected in parallel with the other wire (the common end) connected to the power supply. Then, the resistance between the common terminal and the wire connected to both ends of the voltage was measured with the electric block of the Multimeter. The end with a slightly larger resistance was connected to the other end of the power supply, so that the positive rotation could be achieved. To reverse the connection, the power cable connected to one end of the voltage could be changed to the other end. In terms of the reversing switch connection, the reversing switch had different terminal posts. Taking the common connection method as an example, some of the terminal posts of the reversing switch were connected to the power supply, and some of the terminal posts were connected to the motor winding. The terminal in the middle could be connected to the power supply, and the terminal connected to the main winding and the secondary winding of the motor could change the connection mode through the internal structure of the reversing switch during forward and reverse rotation, thus changing the direction of the current to achieve forward and reverse rotation. For example, during forward rotation, the circuit was connected according to a phase sequence, so that the current flowed through each winding of the motor in turn to achieve forward rotation; when it was reversed, the connection inside the reverse switch changed, changing the current phase sequence in the winding, and then realizing reverse rotation. However, there may be differences in the connection of different models of reversing switch, and the actual operation should be carefully judged. <a href="/?from=ask_words" style="color:red" target="_blank">Read more exciting novels for free</a>
How to connect the five wires of a single-phase motor to the capacity?
In the five-wire single-phase motor, three wires were the main wire, one was the starting wire, and one was the auxiliary wire. Generally, the following methods can be used to connect the voltage: First, distinguish the main winding, the secondary winding, and the starting line of the motor. Generally speaking, the main winding was connected to the power supply, and the secondary winding was connected to the voltage. For the case of five wires, it could be judged by measuring the resistance value first. The two wires with the highest resistance value were connected to the capacity (one of them was the secondary winding wire, and the other was the auxiliary wire such as the starting wire), and the one with the lowest resistance value was connected to the power supply of the main winding wire. If you want to change the direction of the motor, you can swap the specific wires in the motor's lead wire (such as swapping the wire connected to the transformer with other related wires), but the specific operation still needs to be carefully adjusted according to the actual structure and function of the motor. <a href="/?from=ask_words" style="color:red" target="_blank">Read more exciting novels for free</a>
Single-phase 4.5 Kilowatt motor connected with large starting capacity
According to the relationship between the starting capacity and power of a single-phase motor, the starting capacity value corresponding to a 4.5-kilogram motor was not directly mentioned in the existing single-phase motor starting capacity and operating capacity power comparison table. However, according to the usual situation, the running capacity can be estimated to be 2 - 3uF per 100W. 4.5 Kilowatts is 4500W, and the running capacity is about 4500 div100 ×(2 - 3)=90 - 135uF. The starting capacity is usually 2 - 3 times the running capacity, so the starting capacity is about 180 - 405uF. At the same time, the working capacity can also be calculated according to the formula of GC = 1950I/UcosPi (micro-Farad)(I is the motor current, U is the single-phase power supply voltage, cosPi is the power factor, take 0.75), and then the starting capacity can be determined according to the starting capacity of 1 - 4 times the working capacity. However, since the current value is not given, it cannot be accurately calculated. In summary, the starting capacity of a 4.5 Kilowatt motor was about 180 - 405uF. <a href="/?from=ask_words" style="color:red" target="_blank">Read more exciting novels for free</a>