Where are the three slopes?
The places mentioned in " The Past of the Border Waters " included Daban, Daqulin, Qupeng, Mokuang, Xiaomonong, Maniu Town, etc. These place names had the style of Southeast Asia. Not enough TV dramas? Hurry up and click on the books below to read the wonderful original novel!
Three slopes and two slopes square
From the reference materials, it could be seen that the relevant content of the three-slope and two-slope square involved the calculation of earthworks. When constructing such a square, a square grid with a side length of 20m should be made according to the north-south direction (or determined according to the specific conditions of the site). The corner points of the square should be measured on the ground and the ground elevation should be measured. If there is an accurate topographic map, the original terrain elevation of each corner point should be obtained by inserting the method. The square is required to have a 1.5% vertical slope and a 2% horizontal slope, and the earthworks are balanced on the spot. On this basis, the design elevation and the earthworks are calculated. The leveling elevation can be calculated according to the formula 0H = 1/4N *(Eh 1 +2 Eh 2 +3 Eh 3 +4 Eh 4)(where h1 is the elevation of the corner point used once during calculation;h2 is the elevation of the corner point used twice during calculation;h3 is the elevation of the corner point used thrice during calculation;h4 is the elevation of the corner point used four times during calculation). Not enough TV dramas? Hurry up and click on the books below to read the wonderful original novel!
Where is the three slopes of Myanmar?
The prototype of the Three Slopes was the Golden Triangle, located at the junction of Myanmar, Thailand, and Laos. It was the hinterland of Southeast Asia and the triangular zone where Thailand, Myanmar, and Lao were at the intersection. It covered an area of 150,000 to 200,000 square kilometers. This area included Shan State and Kachin State in northern Myanmar, the northern part of Thailand's Qing Rai Province, and the northern part of the Qing Jiang Province, as well as the provinces of Luang Namtha, Phongsali, Udomsay, and the western part of Luang Prabang in Laos. Not enough TV dramas? Hurry up and click on the books below to read the wonderful original novel!
The geographical location of the three slopes
Sanbian Slope was located in the Golden Triangle at the junction of Myanmar, Thailand, and Laos. This area was a triangular area at the junction of Thailand, Myanmar, and Lao. It covered an area of 150,000 to 200,000 square kilometers, including Shan State, Kachin State, the northern part of Thailand's Qing Rai Province, and the northern part of Chang Mai Province, as well as the western part of Lao's Luang Namtha Province, Phongsali Province, Udomsay Province, and Luang Prabang Province. In " The Past of the Border Waters," the crew chose to shoot the scene in Yunnan. Not enough TV dramas? Hurry up and click on the books below to read the wonderful original novel!
What are the archetypes of the three slopes?
The archetypes of the three slopes in the story were the Golden Triangle, Xishuangbanna in Yunnan, and North Myanmar. These places were depicted in novels or movies as having special regional characteristics and were full of various complex social phenomena, such as the chaos and danger in the Golden Triangle and Northern Myanmar, and the ethnic and cultural characteristics of Xishuangbanna. Not enough TV dramas? Hurry up and click on the books below to read the wonderful original novel!
What is the status of the Tapir of the Past in the Three Slopes?
In the three slopes of " The Past of the Border Waters," the local people regarded the tapir as an auspicious object. It had a high status and could be exchanged for many things. It was a symbol of good luck and was considered sacred by everyone. Not enough TV dramas? Hurry up and click on the books below to read the wonderful original novel!
Is the height of the first, second, and third grade slopes the same?
The height of Grade 1, Grade 2, and Grade 3 slopes was different. According to the " Building Slope Engineering Technology Code ", the height of a Grade 1 slope was generally no more than 10 meters, the height of a Grade 2 slope was generally between 10 meters and 30 meters, and the height of a Grade 3 slope was more than 30 meters. Therefore, there was a clear difference in the height of Grade 1, Grade 2, and Grade 3 slopes.
Is the height of the first, second, and third grade slopes the same?
The height of Grade 1, Grade 2, and Grade 3 slopes was different. According to the " Building Slope Engineering Technology Code ", the height of a Grade 1 slope was generally no more than 10 meters, the height of a Grade 2 slope was generally between 10 meters and 30 meters, and the height of a Grade 3 slope was more than 30 meters. Therefore, there was a clear difference in the height of Grade 1, Grade 2, and Grade 3 slopes.
Is the height of the first, second, and third grade slopes the same?
The height of Grade 1, Grade 2, and Grade 3 slopes was different. According to the " Building Slope Engineering Technology Code ", the height of a Grade 1 slope was generally no more than 10 meters, the height of a Grade 2 slope was generally between 10 meters and 30 meters, and the height of a Grade 3 slope was more than 30 meters. Therefore, there was a clear difference in the height of Grade 1, Grade 2, and Grade 3 slopes.
Is the height of the first, second, and third grade slopes the same?
The height of Grade 1, Grade 2, and Grade 3 slopes was different. According to the " Building Slope Engineering Technology Code ", the height of a Grade 1 slope was generally no more than 10 meters, the height of a Grade 2 slope was generally between 10 meters and 30 meters, and the height of a Grade 3 slope was more than 30 meters. Therefore, the height of Grade 1, Grade 2, and Grade 3 slopes were different.
Is the height of the first, second, and third grade slopes the same?
The height of Grade 1, Grade 2, and Grade 3 slopes was different. According to the " Building Slope Engineering Technology Code ", the height of a Grade 1 slope was generally no more than 10 meters, the height of a Grade 2 slope was generally between 10 meters and 30 meters, and the height of a Grade 3 slope was more than 30 meters. Therefore, there was a clear difference in the height of Grade 1, Grade 2, and Grade 3 slopes.