How to deal with the reactor if it doesn't turn?
If the speed of the Huxi HF - 5L variable frequency speed regulation glass reactor was displayed as "0" and the motor did not rotate (that is, it did not turn), the reason might be "motor failure","circuit board failure","start button damage" or "speed regulator damage". The solutions were to contact the manufacturer for assurance after confirming the motor fault, contact the manufacturer for assurance after confirming the circuit board fault, replace the start button, and replace the speed regulator. For other reactors, if they do not turn, first check whether the motor is running normally, such as checking whether the motor rotation direction is correct.(During the initial installation and test run after wire removal and maintenance, it is strictly prohibited to stir in reverse. Normally, it should be clockwise.) Check whether the current value is within the rated range and whether there is any abnormal sound in the motor. Secondly, check whether there are loose parts in the transmission system that affect the steering direction. Also, check whether the packing seal of the stirring shaft is compressed to a moderate degree and whether it hinders the steering direction due to excessive tightness. If the reactor has been repaired before, check whether the installation of each part is correct. Read more exciting novels for free
Is the reactor 201 or 304?
201 stainless steel contains high Manganese, low Ni, poor corrosion resistance, easy to rust;304 stainless steel contains more Chromite, easy to rust, strong corrosion resistance. When choosing the reactor to use 201 or 304 stainless steel, it is necessary to consider the corrosion resistance requirements of the working environment of the reactor. If the working environment is not corrosive and sensitive to cost, 201 stainless steel can be considered; if the working environment has certain corrosive requirements, 304 stainless steel is more suitable. At the same time, we must also consider the standards and specifications of different industries. For example, in industries such as medicine and food that have high requirements for hygiene and corrosion resistance, 304 stainless steel may be a better choice. <a href="/?from=ask_words" style="color:red" target="_blank">Read more exciting novels for free</a>
Neutron reactor
A neutron reactor could be a Neutron reactor. <a href="/?from=ask_words" style="color:red" target="_blank">Read more exciting novels for free</a>
Is the cracking precipitator a reactor?
The FCCU consisted of a reactor (discharger), a regenerating, and other equipment. The discharger was a part of the reactor. It was not an overall concept of the reactor in a separate sense, but a component of the reactor that carried specific functions in the FCCU reaction system. <a href="/?from=ask_words" style="color:red" target="_blank">Read more exciting novels for free</a>
Nuclear fission in the reactor
Take Uranium-235 as an example. When the nucleus of Uranium-235 was bombarded by external neutrons, one nucleus would absorb a neutron and split into two smaller nuclei, releasing two to three neutrons at the same time. The neutrons produced by the fission bombarded another Uranium-235 nucleus, causing new fission. If this continued, it would be a fission chain reaction, which would produce a large amount of heat. In order to achieve such a nuclear fission reaction, the reasonable structure of the reactor should include nuclear fuel, moderator, heat carrier, control facilities, and protective devices. The nuclear fuel needed to be made from uranium ore through processes such as selection, crushing, acid soaking, and concentration to produce a certain amount of uranium and a certain geometric shape of the rod. In a traditional nuclear fission reactor, in order to improve the chain fission reaction efficiency of nuclear fuel, it was necessary to decelerate the high-speed neutrons (fast neutrons) produced by fission into slower neutrons (thermal neutrons). A neutron moderator composed of lighter nuclei (such as light water, heavy water, etc.) would be added to use the hydrogen atoms to decelerate the high-speed neutrons. The heat carrier could be used to take away heat to prevent the reactor from burning down due to overheating. The heat that was extracted could turn the water nuclear reactor into steam to drive the gas turbine to generate electricity. The control facility allowed the nuclear reactor to operate according to human wishes. The protective device was because uranium and fission products were highly radioactive and could cause harm to humans. In addition to the traditional reactors that used Uranium-235 as nuclear fuel, there were also fast neutron reactors (nuclear fission reactors without neutron moderators) and thorium-based molten salt reactors (fourth-generation reactor nuclear energy systems that used thorium as nuclear fuel and composite fluorides as coolants). Their nuclear fission reaction principles were similar, but there were differences in specific fuel, efficiency, safety, and so on. <a href="/?from=ask_words" style="color:red" target="_blank">Read more exciting novels for free</a>
byd reactor principle
In the BYD reactor, fresh and recycled formalin from the formalin plant entered the liquid phase of the BYD reactor, while the ethyne gas entered the bottom of the reactor and dispersed in the liquid-solid phase. Under the effect of the catalyst, the reaction occurred to form 1,4-butynegol (C2H2 + 2HHamster → HOCH2C = ccH20H (BYD)). After the pulp in the ByD reactor was filtered by the candle filter in the reactor, the filtered liquid entered the ByD collection tank (BD-V104). The reactor's internal components included a candle filter, an ethyne loop, a stirring device, a cooling coil, etc. The shell was made of Q345R + 316L. <a href="/?from=ask_words" style="color:red" target="_blank">Read more exciting novels for free</a>
The filter in the photocatalysis reactor
The optical filter in the photocatalysis reactor played an important role in many aspects. First of all, it could filter light and only allow light of a specific wavelength to pass through, thereby achieving fine control of the reaction light source, which helped to improve the specialization and efficiency of the biochemical reaction. Secondly, different filter had different spectral transmissances, which could be used to control the light intensity and spectral distribution during the reaction process. This would not only help in the optimization of experimental conditions and increase the purity and yield of the product, but also help to reduce the occurrence of side reactions and reduce energy consumption and experimental costs. In addition, the filter also had the function of protecting the photocatalysis reactor. Some light sources would generate high temperatures during long-term operation, which could cause the performance of the instrument to decline or even be damaged. The filter could effectively filter out excess light and reduce the heat of the light source, thereby extending the service life of the instrument. <a href="/?from=ask_words" style="color:red" target="_blank">Read more exciting novels for free</a>
Esterification reactor assembly
The manufacturing and assembling of a resin-catalyze esterfication reactor includes the following steps: firstly, manufacturing a reactor main body, welding a bottom installation flange-plate at the bottom of the reactor main body, and a top installation flange-plate at the top of the reactor main body; secondly, carrying out the operation of welding auxiliary installation components, such as welding a number of auxiliary installation hanging ears on the outer side of the reactor main body; Finally, the assembly process. Moreover, the bottom mounting flange-plate and the top mounting flange-plate were provided with a number of flange-connecting holes, and the top connecting flange-plate and the bottom connecting flange-plate were also provided with a number of flange-connecting holes, which may be used to connect or fix related components during the assembly process. <a href="/?from=ask_words" style="color:red" target="_blank">Read more exciting novels for free</a>
Fast breeder reactor
The English translation of the fast neutron breeder reactor was "fast breeder reactor", which could also be translated as "fast neutron breeder reactor". <a href="/?from=ask_words" style="color:red" target="_blank">Read more exciting novels for free</a>
Laboratory foaming reactor
Control the temperature of the reactor
There were many options for the temperature control of the reactor. Some powerful manufacturers would provide customized reaction kettle thermostats according to customer needs. For example, the thermostats of the reaction kettle were customized with parts from domestic and foreign brands, which could increase the service life of the parts; the electric cabinet was isolated from the body, which was effective in heat insulation, which could extend the service life of the electrical appliances; the automatic exhaust function and instant cooling function were available when the machine was turned on to ensure the safety of use. The temperature control accuracy of its products can reach +/-1 ° C, the cooling power can be provided from 6KW to 1200KW, and the temperature range is from-100 ° C to 300 ° C, which can meet the needs of most enterprises for constant temperature control. In addition, Ou Neng Machinery could also provide heating and cooling solutions for the reactor. When choosing the reactor temperature control supply, in addition to considering the equipment itself, you should also pay attention to the after-sales of the manufacturer. For example, a powerful manufacturer can customize a suitable product before purchase. If there is a problem after purchase, they can send professional technicians to solve it. Small manufacturers may lack professional technical teams and it is difficult to find the problem in time when encountering technical problems. <a href="/?from=ask_words" style="color:red" target="_blank">Read more exciting novels for free</a>