webnovel
Will the sunken drainage on the same floor reverse the smell?

Will the sunken drainage on the same floor reverse the smell?

2026-11-19 20:55
1 answer

Submerged drainage on the same floor might reflect the stench. The main reasons for its anti-odor are as follows: 1. [Natural Dissipation: The smell in the sewers is unpleasant to begin with, and the air in the sewers will scatter out through the various sewers.] Due to the lack of pressure in the sewers, the sewage could not fill the pipes. There was a large amount of air and organisms in the sewers, which could cause the odor to spread. 2. Pressure increase in the pipe: When the residents in the same building concentrate on draining the sewer (such as before going to work in the morning), the sudden increase in the amount of water in the pipe will increase the pressure, and the air squeezed out of the pipe will emit a stench through the outlet. 3. Room pressure reduction: For example, when the range hood works, it will produce negative pressure, sucking away a large amount of air in the room, causing the room pressure to decrease. The air in the pipe that is higher than the room pressure will flow back into the room, and the air in the pipe will have a smell, resulting in a reverse odor phenomenon. In order to prevent the sinking type of same-floor drainage from smelly, the following measures can be taken: 1. Water trap installation: The water trap (such as S-bend, U-bend) at the bottom of the water trap forms a water seal, which can block the air in the pipe from entering the room. However, the water trap will reduce the drainage speed and is easy to block. New buildings generally do not install it. If the user of the same floor drainage (sunken toilet) is installed, the maintenance difficulty after blockage should be considered. 2. Use anti-odor devices: For example, use a three-way anti-odor sewer in the kitchen, install a sealing plug at the drain of the vegetable basin, and use a floor drain with a water seal and anti-odor. 3. Reasonably design the drainage system: The caisson-type toilet can be equipped with secondary drainage. A drainage outlet can be set at the bottom of the caisson-type toilet to discharge the water and water that has not been discharged from the first drainage outlet (such as the floor drain that is close to the floor tile) in time to keep the toilet clean and fresh and reduce the source of odor. Read more exciting novels for free

The same floor drainage, the second floor does not reverse the water, why?

There may be the following reasons why the second floor of the same floor did not reverse the water: First, if the sewer pipe was not blocked, it would usually not reverse the water. Secondly, the design of the pipeline was reasonable and the construction was correct. For example, the inner diameter of the pipeline was suitable, there were no foreign objects inside, no damage, there were not many bends, and the slope angle was reasonable. Moreover, during the renovation of the house, the construction workers did not leave any gravel, cement, or other construction waste inside the pipeline. In addition, the upstairs owner used it properly and did not pour hair, paper towels, leftovers and other domestic garbage into the pipe to cause blockage. It was also possible that the hydraulic conditions were good. When the residential drainage was gravity drainage, the sewage could be smoothly discharged from the sanitary ware into the drainage vertical pipe, then into the drainage horizontal main pipe, and finally into the outdoor drainage inspection well. <a href="/?from=ask_words" style="color:red" target="_blank">Read more exciting novels for free</a>

1 answer
2026-07-16 02:07

same floor drainage

Same-floor drainage was a drainage method for sanitary appliances. Its characteristic was that the drainage pipe did not need to pass through the floor, but was laid in the same floor and connected to the drainage standpipe. There were two main forms of same-floor drainage: wall-row zero-drop same-floor drainage and slightly-drop same-floor drainage. The wall row zero-drop drainage on the same floor meant that the drainage pipe went along the wall and did not occupy the vertical floor height. The bathroom could maintain the same floor height as other rooms, and the design freedom was higher, and it was beautiful and practical. The same floor drainage with micro-descending plates was a common form in China. It required the installation of dry area floor drain, which could almost achieve zero floor height difference without occupying vertical floor height. The difference between the same floor drainage and the different floor drainage was the layout of the bathroom appliances, the aesthetics of the house, and the drainage noise. The advantages of same-floor drainage were high degree of freedom in layout, beautiful houses, and low drainage noise, but there were also shortcomings such as high construction cost and difficult maintenance. In general, same-floor drainage was a healthier, more convenient, and more beautiful drainage method.

1 answer
2025-01-12 05:07

The drainage pipe is blocked, and the third floor is flooded.

There could be many reasons for the blockage of the drainage pipe and the water on the third floor could be reversed, and different solutions could be taken. ** I. Cause Analysis ** 1. ** Congestion ** - Hair, kitchen waste (rice, vegetable leaves, noodles, etc.), grease (such as lard), and other sundries may have accumulated in the pipeline, causing poor drainage and water flow to fail smoothly, resulting in water reversal on the third floor. - It could be that the pipes at the lower levels were blocked, such as the pipes below the second floor, causing the water above the third floor to be unable to drain normally and turn against the water. 2. ** In terms of installation ** - If the drainage pipes on the third floor were not installed reasonably, such as the installation position of the drainage hose being too low, it would make it easy for water to accumulate and not be discharged in time, causing water to reverse. ** 2. Solution ** 1. ** Temporary measures ** - A sealing ring could be placed at the drain outlet of the reverse water. This would fix the sewer pipe and block the gap between the hose and the sewer pipe. To a certain extent, it would reduce the reverse water situation. Even if the water flow was fast, it was not easy for the water to return from the drain. 2. ** Clear the blockage ** - ** Chemistry ** - He could use the vinegar and soda method to first drain the water in the sewer, then mix the white vinegar and soda powder, and then add hot water into the sewer to use a chemical reaction to dissolve the blockage. - The salt and soda method was also feasible. Mix 1/2 cup of salt and 1/2 cup of soda water and pour them into the sewer. This mixture would help remove the dirt on the inner wall of the pipe, expand the diameter of the pipe, and dredge the pipe. - You can also use a pipe dredge agent. According to the instructions, you usually add an appropriate amount of dredge agent and warm water (no more than 60 degrees) to make it react in the pipe and dissolve the blockage, such as hair, meat, vegetable leaves, etc. - ** Physical method ** - Using the hot water method, boiling hot water was poured into a kettle or pot, and a towel was used to block the sewer to maintain the temperature and pressure of the hot water. The flushing and softening effect of the hot water was used to dredge the pipe. - The pump method could also be tried. First, the mouth of the sewer was blocked, and fresh water was poured in. Then, the pump was continuously pumped, and through the up and down circulation, pressure was formed. The external water pressure was used to dredge the sewer, but this method was more cumbersome. - The mop method. If the blockage was urgent, the mop could be used to directly block the drain, creating pressure back and forth. Repeat 5 - 10 times to discharge the blockage. - The mineral water bottle method was to cut off the bottom of the mineral water bottle, put on gloves, and insert the mineral water bottle vertically into the sewer. Repeatedly lift and press down, and discharge the foreign matter in the sewer through the huge pressure formed in the bottle. If the toilet was blocked and the bottle was not high enough, the insulation tape could be used to stick the 502 to the disposable chopsticks and the bottle cap firmly before continuing the operation. After dredging, he had to use half a bowl of white vinegar, five pump of dishwashing liquid, and three spoonfuls of baking soda mixed with boiling water to pour it into the sewer for deep cleaning to prevent secondary blockage. 3. ** Protective measures ** - When installing the pipe, whether it was the sewer pipe of the vegetable basin or the pipe under the bathroom cabinet, it must be higher than the ground. At the same time, the water hose should be plugged in to help prevent water from flowing back. <a href="/?from=ask_words" style="color:red" target="_blank">Read more exciting novels for free</a>

1 answer
2026-07-12 20:48

Must the drainage pipe have a reverse flow?

The drainage pipes did not necessarily have to have water reversal. The reason for the flooding was usually due to blockage of the pipeline, poor drainage of the public pipeline (such as the accumulation of water in the rainstorm could not be discharged in time), unreasonable pipeline design (such as the material and angle of the drainage pipeline on the second floor), improper use by the user (throwing debris into the pipeline), or poor maintenance of the property (not clearing the pipeline in time). Under normal circumstances, if the pipeline was smooth, reasonably designed, used correctly, and well maintained, the drainage pipeline would not be flooded. <a href="/?from=ask_words" style="color:red" target="_blank">Read more exciting novels for free</a>

1 answer
2026-11-19 10:38

The first floor has independent drainage. Will it turn against the water?

Under normal circumstances, if the first floor used independent drainage, the probability of water betrayal was extremely low. However, in some special circumstances, they could still betray the court. Judging from the location of the blockage, if there was a blockage below the main sewage pipe, once the sewage was not discharged smoothly, the sewage might flow back to the outlet closest to the blockage point. This blockage might cause the water on the first floor to reverse. Judging from the condition of the pipeline itself, for houses before 2000, the age of the house was more than 20 years old, the pipeline was aging, and the cast iron sewer pipe was used. The pipe wall was rough and easy to rust, and dirt was easy to hang on the wall. Some of them used old-fashioned squatting, which was easy to rush debris into the pipeline and cause blockage. In this case, even the first floor with independent drainage had the risk of water rebellion. In addition, if there are undissolved substances entering the pipeline, such as construction waste (cement, sand, etc.) or domestic waste (rags, plastic products, sanitary napkins, etc.), the long-term accumulation of blockage at the elbow at the end of the pipeline may also cause water reversal. <a href="/?from=ask_words" style="color:red" target="_blank">Read more exciting novels for free</a>

1 answer
2026-11-09 05:23

Will the toilet on the first floor still smell bad now?

If effective anti-odor measures were not taken, the toilet on the first floor might still smell bad. The anti-odor of the toilet may be due to blockage and aging and loosening of the collar. The anti-odor of the sink pipe may be due to poor sealing of the pipe or insufficient water in the trap. The anti-odor of the floor drain may be due to the poor odor removal effect of the floor drain itself or the lack of water in the floor drain. Poor ventilation at the exhaust vent may also lead to odor. In addition, the blockage of the sewer and the poor sealing of the water pipe would also cause a reverse smell phenomenon. <a href="/?from=ask_words" style="color:red" target="_blank">Read more exciting novels for free</a>

1 answer
2026-10-05 00:43

Is there any way to reverse the sewage on the first floor?

There were several ways to prevent the sewage from flowing back on the first floor: 1. When designing basements or toilets, the location of the sewage discharge outlet should be designed to be higher than the municipal sewage pipe to prevent the sewage from flowing back. 2. A closed sewage lifting device was used to lift and discharge the sewage. This device had the function of a check valve, which could effectively prevent the sewage from flowing back. 3. Check if the sewer pipe is blocked. If it is caused by the blockage of the sewer pipe, you can ask the property management to check and change it into an independent pipe to discharge it directly outside the building to keep the sewer unobstructed. 4. Check if there is any exhaust problem. Ask the property company if there is an exhaust hole when installing the pipe. If there is no such hole, you can contact the property company together with other residents to solve it. Please note that the above methods are only for reference. The specific solutions need to be adjusted according to the actual situation.

1 answer
2025-01-08 18:08

4th floor toilet anti-reverse valve

As for the anti-reverse water valve in the toilet on the fourth floor, if it was an anti-reverse water valve in the toilet sewer, a brass non-return valve could be used. It could be installed at the corner valve of the toilet, and the connection of the toilet hose could be unscrewed. The non-return valve could be installed on the corner valve, and then the hose could be connected. If the bathroom cabinet drainage pipe is ground drainage, a vertical check valve can be installed; if the bathroom cabinet drainage pipe is changed to wall drainage, a horizontal check valve can be installed. When installing the vertical check valve, if the bottom of the bathroom cabinet is more than 20 cm from the ground, the check valve set can be installed under the bathroom cabinet; if it is less than 20 cm, the check valve needs to be installed inside the cabinet. When installing the wall drain pipe check valve, the 90° out of the wall of the drain pipe should be directly connected to the loose joint check valve; if the 45° out of the wall of the drain pipe needs to add a 45° elbow to be changed into a horizontal pipe, then connect the loose joint check valve. If you are worried that the loose knot will affect the closing of the cabinet door, you can remove it, but this way, you can't disassemble the check valve as a whole. <a href="/?from=ask_words" style="color:red" target="_blank">Read more exciting novels for free</a>

1 answer
2026-08-23 07:24

How to get rid of the anti-tide smell of the wooden floor

Here are some ways to get rid of the anti-damp smell of wooden flooring: 1. ** Use mold removal agent and freshener **: If the odor is caused by moisture and mold, you can spray mold removal agent on the damp and moldy parts of the floor first. After waiting for a while, wipe it clean with water, and then use freshener to remove the moldy smell. 2. ** Maintain ventilation **: Maintain ventilation in the room to help disperse the odor of the floor due to moisture. 3. ** Use activated carbon, drying agent or dry lime **: Buy activated carbon, or use drying agent or dry lime to remove moisture and reduce odor. 4. ** Using natural objects to remove odor **: You can place orange peels, lemon peels, and other items in the room, but this method may not be effective quickly. You can also fill a container with cold water and add a suitable amount of vinegar in the room to speed up the elimination of residual smell. You can also use pineapple to remove odor. Put a few pineapples in each room (more can be placed in large rooms). Pineapples can absorb the odor and also emit a fragrance. 5. ** Use a odor-removing cleaner **: You can choose some imported high-tech odor-removing cleaners. These cleaners can remove the harmful gases emitted by the wooden floor. Pouring them into a plate and placing them in the room, combined with scrubbing and odor-removing methods, can effectively remove the unpleasant smell after a few days. 6. ** Plant Absorption Method **: Place cacti, spider plants, gerbera flowers (Gerbera), reeds, ivy, sago, chrysanthemums, and other plants at home. These plants can absorb harmful gases such as Formalide. Among them, ivy, sago, chrysanthemums, etc. can also eliminate Xylane. <a href="/?from=ask_words" style="color:red" target="_blank">Read more exciting novels for free</a>

1 answer
2026-08-07 06:20

Is it useful to install a reverse valve on the second floor? Is it safe?

The non-return valve was useful in solving the problem of the second floor. The non-return valve could prevent the sewage from flowing back into the second floor from the sewer, and it was relatively simple to install and low in cost. However, the check valve required regular maintenance to ensure that it worked properly. In terms of safety, if a check valve was installed on the second floor, it might affect the third floor in the event of water reversal. However, if the drainage system was properly maintained and inspected while the check valve was installed, this risk could be reduced to a certain extent. There were also some precautions when choosing a check valve. For example, don't choose a spring-type one (if the seal is too long, the spring will loosen, which means that it will not be installed). You should choose a silica gel molded one. The raw material is ABS. This kind of check valve is anti-oil, high-temperature resistant, sturdy and not deformed. It can be used from 15 cm to 20 cm. Even if you change the smoke machine in the future, you don't need to change the check valve. To sum up, installing a check valve was a feasible solution to the problem of water reversal on the second floor, but it was necessary to consider the subsequent impact and do a good job in maintenance and other related work. <a href="/?from=ask_words" style="color:red" target="_blank">Read more exciting novels for free</a>

1 answer
2026-08-17 13:46
a
b
c
d
e
f
g
h
i
j
k
l
m
n
o
p
q
r
s
t
u
v
w
x
y
z