webnovel
Must the drainage pipe have a reverse flow?

Must the drainage pipe have a reverse flow?

2026-11-19 10:38
1 answer

The drainage pipes did not necessarily have to have water reversal. The reason for the flooding was usually due to blockage of the pipeline, poor drainage of the public pipeline (such as the accumulation of water in the rainstorm could not be discharged in time), unreasonable pipeline design (such as the material and angle of the drainage pipeline on the second floor), improper use by the user (throwing debris into the pipeline), or poor maintenance of the property (not clearing the pipeline in time). Under normal circumstances, if the pipeline was smooth, reasonably designed, used correctly, and well maintained, the drainage pipeline would not be flooded. Read more exciting novels for free

Spiral drainage pipe

Spiral drainage pipe was a kind of pipe used in building drainage system, which had some characteristics and advantages. Spiral drainage pipe has the following characteristics: 1. Reduce noise: The design of the spiral drainage pipe can effectively reduce the noise pollution caused by drainage. The measured results showed that compared with the traditional cast iron drainage pipe, the noise of the spiral drainage pipe was about 2 to 4 decibels lower, and it had a silencing effect. 2. To prevent the damage of the floor drain seal: The spiral structure inside the spiral drainage pipe can reduce the pressure fluctuation in the pipe, avoid the damage of the water seal caused by the negative pressure of the upper user and the positive pressure of the bottom user, and improve the stability of the drainage system. 3. Increase drainage efficiency: The internal spiral structure of the spiral drainage pipe increases the friction resistance of the water flow, preventing the water flow from blocking the pipe due to inertia, improving drainage efficiency and reducing the occurrence of blockage accidents. 4. [Double silencing effect: Hollow wall spiral drainage pipe is a special structure of spiral drainage pipe. It has a double-layer structure and honeycomb-shaped holes, which can further isolate noise and have a better silencing effect.] In general, the spiral drainage pipe had the advantages of reducing noise, preventing the damage of the floor drain seal, and improving drainage efficiency. They are commonly used in the drainage system of buildings, especially for the drainage of single standpipes in high-rise buildings.

1 answer
2025-01-08 20:31

Open ditch drainage and underground pipe drainage

Open ditch drainage and underground pipe drainage were two common methods of farmland drainage. Open ditch drainage was a method of digging drainage ditches to form a drainage ditch network. Water would flow from the field ditch network into the water transmission ditch network and finally into the drainage area (river, lake, sea). Underground drainage was a method of burying pipes underground to drain water by removing excess water from the farmland soil and lowering the water level. The underground pipe drainage could be used to filter and seep water by using sand and stone bedding, laying thick plastic pipes and crushed sand. Open ditch drainage was suitable for soil layers with better geological conditions, while underground pipe drainage could effectively control the underground water level, save land, and have a better drainage effect.

1 answer
2025-01-11 06:43

The horizontal drainage pipe is connected with the horizontal pipe

The horizontal drainage pipes shall be connected with the horizontal drainage pipes by oblique three-way, oblique four-way or three-way and four-way along the water. To be specific, the connection between the horizontal sewage pipes should not be made with a straight three-way or a straight four-way, but with an inclined three-way or an inclined four-way or a straight three-way or a straight four-way. These connections could ensure the normal operation and drainage effect of the drainage pipeline.

1 answer
2025-01-11 09:45

Horizontal branch pipe and horizontal main pipe of drainage

Horizontal branch pipes and horizontal main pipes were two types of pipes in the drainage system of buildings. The horizontal branch pipe was a horizontal pipe section connecting the sewage collection device drain pipe and the vertical drainage pipe, and was used to send sewage from the sewage collection devices to the vertical drainage pipe. The horizontal branch pipe should have a certain slope to facilitate smooth drainage. The horizontal main pipe was a pipe section that connected several drainage vertical pipes to the discharge pipe, mainly to receive the drainage of the horizontal branch pipe. The connection point of the horizontal branch pipe and the horizontal main pipe has a certain distance from the bottom of the vertical drainage pipe to ensure the normal operation of the drainage system. The specific connection requirements could refer to the relevant specifications and design standards.

1 answer
2025-01-12 18:50

The difference between upvee spiral pipe and drainage pipe

The difference between the UpPVP spiral pipe and the drainage pipe was that the UpPVP spiral pipe was a special type of drainage pipe with a noise reduction function. The inner wall was smooth, and the noise during drainage was low. The drainage pipe was an ordinary pipe with no noise reduction function. Therefore, the upvee spiral pipe could reduce noise during the drainage process, but the drainage pipe did not have this function.

1 answer
2025-01-12 12:38

The drainage horizontal branch pipe is connected with the vertical pipe.

When the horizontal drainage branch pipe is connected to the vertical pipe, different connection methods can be used. According to the Design Standard for Building Water and Waste Water, when the sanitary ware drainage pipe is vertically connected to the horizontal drainage pipe, a 90° inclined tee should be used. When the horizontal branch pipe is connected with the vertical pipe, it can adopt a three-way or four-way downstream pipe and a 45° inclined three-way or 45° inclined four-way pipe. In a special single-standpipe system, the horizontal branch pipe and the standpipe can be connected by special accessories. In addition, according to some provisions of the Building Water and Waste Design Code, when the drainage stand pipe is only equipped with a top vent pipe, the vertical distance between the lowest drainage horizontal branch pipe and the stand pipe bottom shall not be less than the specified distance. According to the Connection Design and Material Selection of Building Drainpipe Branch and Horizontal Main, when the drainage branch pipe on the upper layer of the horizontal main drainage pipe is connected to the horizontal main drainage pipe, it is recommended to use a 45° inclined tee to connect it from the top of the horizontal main drainage pipe. To sum up, when the horizontal drainage branch pipe is connected to the vertical pipe, different connection methods such as 90° inclined three-way, downstream three-way or downstream four-way, 45° inclined three-way or 45° inclined four-way can be used.

1 answer
2025-01-12 03:39

What's a horizontal drainage pipe?

The horizontal main drainage pipe was a horizontal pipe section connecting the drainage pipe of the sewage collection device and the vertical drainage pipe. It could send the sewage flowing out of the sewage collection device to the vertical drainage pipe. It should have a certain slope, and the end connected to the drainage stand pipe should be lower to facilitate drainage.

1 answer
2025-01-10 22:39

The drainage branch pipe is connected to the horizontal main pipe by 0.6m.

When the drainage branch pipe is connected to the horizontal main pipe, the connection point shall not be less than 0.6 meters below the turning point.

1 answer
2025-01-12 05:58

installation method of horizontal drainage branch pipe

There were several different ways to install the horizontal drainage pipe. First, you can choose to hang the pipeline under the floor of this floor, also known as "non-same floor drainage" or "suspended drainage under the floor". Secondly, you can choose to lay pipes in the refill layer when the bathroom floor structure is sinking, which is also called "same-floor sinking drainage". In addition, they could also choose to install the pipeline on the ground of this floor, which was also called "same-floor drainage". The specific installation method needed to be selected and operated according to the actual situation and design requirements.

1 answer
2025-01-14 14:35

The drainage pipe is blocked, and the third floor is flooded.

There could be many reasons for the blockage of the drainage pipe and the water on the third floor could be reversed, and different solutions could be taken. ** I. Cause Analysis ** 1. ** Congestion ** - Hair, kitchen waste (rice, vegetable leaves, noodles, etc.), grease (such as lard), and other sundries may have accumulated in the pipeline, causing poor drainage and water flow to fail smoothly, resulting in water reversal on the third floor. - It could be that the pipes at the lower levels were blocked, such as the pipes below the second floor, causing the water above the third floor to be unable to drain normally and turn against the water. 2. ** In terms of installation ** - If the drainage pipes on the third floor were not installed reasonably, such as the installation position of the drainage hose being too low, it would make it easy for water to accumulate and not be discharged in time, causing water to reverse. ** 2. Solution ** 1. ** Temporary measures ** - A sealing ring could be placed at the drain outlet of the reverse water. This would fix the sewer pipe and block the gap between the hose and the sewer pipe. To a certain extent, it would reduce the reverse water situation. Even if the water flow was fast, it was not easy for the water to return from the drain. 2. ** Clear the blockage ** - ** Chemistry ** - He could use the vinegar and soda method to first drain the water in the sewer, then mix the white vinegar and soda powder, and then add hot water into the sewer to use a chemical reaction to dissolve the blockage. - The salt and soda method was also feasible. Mix 1/2 cup of salt and 1/2 cup of soda water and pour them into the sewer. This mixture would help remove the dirt on the inner wall of the pipe, expand the diameter of the pipe, and dredge the pipe. - You can also use a pipe dredge agent. According to the instructions, you usually add an appropriate amount of dredge agent and warm water (no more than 60 degrees) to make it react in the pipe and dissolve the blockage, such as hair, meat, vegetable leaves, etc. - ** Physical method ** - Using the hot water method, boiling hot water was poured into a kettle or pot, and a towel was used to block the sewer to maintain the temperature and pressure of the hot water. The flushing and softening effect of the hot water was used to dredge the pipe. - The pump method could also be tried. First, the mouth of the sewer was blocked, and fresh water was poured in. Then, the pump was continuously pumped, and through the up and down circulation, pressure was formed. The external water pressure was used to dredge the sewer, but this method was more cumbersome. - The mop method. If the blockage was urgent, the mop could be used to directly block the drain, creating pressure back and forth. Repeat 5 - 10 times to discharge the blockage. - The mineral water bottle method was to cut off the bottom of the mineral water bottle, put on gloves, and insert the mineral water bottle vertically into the sewer. Repeatedly lift and press down, and discharge the foreign matter in the sewer through the huge pressure formed in the bottle. If the toilet was blocked and the bottle was not high enough, the insulation tape could be used to stick the 502 to the disposable chopsticks and the bottle cap firmly before continuing the operation. After dredging, he had to use half a bowl of white vinegar, five pump of dishwashing liquid, and three spoonfuls of baking soda mixed with boiling water to pour it into the sewer for deep cleaning to prevent secondary blockage. 3. ** Protective measures ** - When installing the pipe, whether it was the sewer pipe of the vegetable basin or the pipe under the bathroom cabinet, it must be higher than the ground. At the same time, the water hose should be plugged in to help prevent water from flowing back. <a href="/?from=ask_words" style="color:red" target="_blank">Read more exciting novels for free</a>

1 answer
2026-07-12 20:48
a
b
c
d
e
f
g
h
i
j
k
l
m
n
o
p
q
r
s
t
u
v
w
x
y
z