webnovel
What should I use to measure the voltage of 1140?

What should I use to measure the voltage of 1140?

2026-11-22 01:56
1 answer

For measuring a voltage of 1140 volts, several tools can be considered. A voltmeter, which is specifically designed to measure voltage, can be a good choice. There are also some advanced multimeters. For example, some digital multimeters are capable of accurately measuring high voltages like 1140 volts. Additionally, specialized high - voltage test instruments can also be used for such measurements. Read more exciting novels for free

How to measure the voltage of the port of the single-chip computer with a universal meter?

When testing the voltage at the port of the single-chip computer with a universal meter, connect the red pen to the port pin of the single-chip computer, connect the black pen to the GND (ground), and then read the voltage displayed by the universal meter. It should be noted that the operating voltage range of different MCUs is different. For example, the normal operating voltage range of the STC89C52RC is 5.5V - 3.4V, and the most commonly used voltage in this range is 5V. If the ATmega single-chip processor was used, it was impossible to measure the resistance between the output high-level IO-to-GND or the output low-level IO-to-vcc-resistance due to the existence of the output static voltage. <a href="/?from=ask_words" style="color:red" target="_blank">Read more exciting novels for free</a>

1 answer
2026-07-11 18:01

How much voltage does the surveillance camera use?

The voltage of the surveillance cameras was 220V AC, 24V AC, and 12V AC. In most cases, when the distance is relatively close, you can choose the 12V power supply; if the camera is far away from the host and other special circumstances, it is recommended to choose the AC 24V, because under the same transmission distance, the higher the voltage, the smaller the power loss, and the higher the output power. This can ensure that the camera has sufficient power supply. <a href="/?from=ask_words" style="color:red" target="_blank">Read more exciting novels for free</a>

1 answer
2026-08-06 09:19

Is there a relationship between the discharge of the voltage and the reverse voltage? Why?

The discharge of the electric capacity was not directly related to the reverse voltage. Capacitive discharge was based on the characteristics of the transformer itself. When the transformer was charged and disconnected from the power supply, the charges on the two polar plates would flow from one plate to the other plate through the external circuit under the effect of the electric field force, forming a current and then discharge. This process was mainly affected by the voltage of the transformer itself, the amount of charge and the resistance in the circuit. The larger the voltage and the amount of charge, the slower the discharge process, and the smaller the resistance, the faster the discharge process. Reverse voltage refers to the voltage applied to a component such as a semiconductor in the opposite direction of normal operation. It is a concept for polar components such as a semiconductor. It is not directly related to the charge flow and electric field change mechanism based on the principle of discharge. <a href="/?from=ask_words" style="color:red" target="_blank">Read more exciting novels for free</a>

1 answer
2026-09-27 18:10

Cause of single-phase voltage fluctuation in low-voltage line

Based on context alone The single-phase voltage fluctuation of low-voltage lines mainly has the following reasons: ** 1. Power Source Side ** 1. ** The generator output is unstable ** - The speed fluctuation of the generator will affect the frequency and magnitude of the output voltage. For example, when the speed governing system of the generator's prime motor (such as a steam turbine or a water turbine) fails, the speed may change. If the rotation speed increases, according to the formula [E = 4.44fN 'Phi]([E] is the induced EMF,[f] is the frequency,[N] is the number of coil turns, and [Phi] is the magnetic flux), the frequency [f] increases, and the induced EMF [E] also increases, causing the output voltage to fluctuate. 2. ** Transformer problem ** - The tap setting of the transformer was unreasonable. If the tap position of the transformer was not selected properly, for example, when the voltage needed to be increased, the tap was set to the step-down position, which would cause the output voltage to deviate from the rated value and cause voltage fluctuations. - Transformer malfunction. If the winding was short-circuited, it would change the equivalent induction and resistance of the transformer, thus affecting the voltage output. After a turn-to-turn short circuit, the short-circuit winding's inductivity will decrease. According to U = L_frac{di}{dt}_(U_is the voltage, L_is the inductivity, I_is the current, and t_is the time), the voltage will decrease under the condition that the current rate of change is constant. Due to the unstable state of the short-circuit fault, the voltage will fluctuate. ** 2. Load-side factor ** 1. ** Connection and removal of high-power single-phase load ** - When high-power single-phase equipment (such as large welding machines, single-phase electric furnaces, etc.) suddenly connected to the low-voltage line, it would cause a sudden increase in the line current. According to the value of U = IG (U = IG)(U = voltage, I = current, and R = line resistance), the voltage drop on the line will increase, causing the voltage at the load to decrease. When these devices were suddenly removed, the current would decrease rapidly, and the voltage would rise again, causing voltage fluctuations. 2. ** Unbalanced load ** - In a three-phase four-wire low-voltage system, if the three-phase load was seriously unbalanced, there would be a current flowing through the neutral wire. When there is resistance in the neutral line, there will be a voltage drop of U_N = I_NRN (U_N is the neutral line voltage drop, I_N is the neutral line current, and R_N is the neutral line resistance), which will cause the single-phase voltage to fluctuate. For example, if a certain phase is overloaded, the voltage of that phase will decrease, and the voltage of the light-loaded phase will increase. ** 3. Route factor ** 1. ** Line Resistance ** - The aging of the line or the small diameter of the line will increase the resistance of the line. When the load current passes through, according to U = IG, a large voltage drop will occur. As the load current changed, the voltage drop would also change, causing voltage fluctuations. 2. ** Line inductivity and capacity ** - Long-distance low-voltage lines had the effect of inductance and capacity. When the current in the circuit changed, the inductors would generate an induced electromagnetic force to hinder the change in the current, and the condensers would charge and discharge. These processes would cause fluctuations in the line voltage. For example, in some rural long-distance low-voltage power supply lines, the influence of this kind of inductance and capacity may be more obvious. <a href="/?from=ask_words" style="color:red" target="_blank">Read more exciting novels for free</a>

1 answer
2026-06-28 13:32

What's the difference between battery voltage and cell voltage?

The battery voltage refers to the voltage of the entire battery, while the cell voltage refers to the voltage of the individual battery cells that make up the battery. For a battery consisting of multiple cells in series (such as a lead-acid battery consisting of N 12V cells in series), the battery voltage is the total voltage after the cell voltage is combined in series. For example, 16 strings of 48 volts of iron lithium, 16 units in series, and the corresponding voltage of each unit together constituted the 48 volts of the entire battery. Different charging and discharge conditions affect the cell voltage, which in turn affects the battery voltage. The difference in cell voltage will also have different effects on the battery's performance and life. For example, the greater the difference in cell voltage, the shorter the battery's life. <a href="/?from=ask_words" style="color:red" target="_blank">Read more exciting novels for free</a>

1 answer
2026-07-01 06:05

The greater the current of the voltage meter, the smaller the voltage meter value

The higher the voltage, the smaller the value. <a href="/?from=ask_words" style="color:red" target="_blank">Read more exciting novels for free</a>

1 answer
2026-08-11 05:18

Normal battery voltage

For camera batteries, the general nominal voltage was 7.2V, and the discharge and full voltage range was about 7.4 - 8.4V, which could be as wide as 7.2 - 8.4V. However, there were also cases where the battery voltage was 3.6V. For example, the battery voltage of the Canon BG- 718 was 3.6V. <a href="/?from=ask_words" style="color:red" target="_blank">Read more exciting novels for free</a>

1 answer
2026-07-22 21:46

Reverse voltage multiplication

There were several ways to achieve inverse voltage multiplication: 1. The input voltage was raised using a transformer, and then converted to a reverse voltage through a rectify circuit. 2. Using a voltage doubler circuit, the voltage was increased by connecting multiple reactors in series. 3. A voltage doubler circuit was used to increase the voltage through a multi-stage rectify and filter. 4. Using a voltage amplifier to amplify the input signal to increase the reverse voltage, the negative feedback method can be used to connect the amplifier circuit to obtain the reverse proportional voltage. In addition, there are also chip TC682IOA, TC682COA inverted voltage multiplying IC chips that can be used in related circuits. <a href="/?from=ask_words" style="color:red" target="_blank">Read more exciting novels for free</a>

1 answer
2026-09-08 00:20
a
b
c
d
e
f
g
h
i
j
k
l
m
n
o
p
q
r
s
t
u
v
w
x
y
z