How to change the sewer pipe on the second floor

The sewer pipe connected to the rainwater pipe and turned the water around. <a href="/?from=ask_words" style="color:red" target="_blank">Read more exciting novels for free</a>

In the case of no damage, the floor heating pipe could usually be used for 50 years, the same life as the building, but this was also affected by the material of the pipe, the environment, and other factors. The water collectors, thermostats, and other components in the floor heating system needed to be replaced once every ten years or so. If the floor heating pipe is not damaged by external forces, corrosion, etc., and can work normally, it may not need to be replaced for 20 years. However, if there are situations such as pipeline aging (such as frequent use of high-temperature water to accelerate aging), frequent failures, poor water flow affecting heating, etc., you need to consider replacing it. At the same time, daily use should also pay attention to maintenance, such as avoiding random drilling and slotting on the ground, controlling the water temperature of the floor heating pipe is not high, cleaning the floor heating pipe every two or three years, etc. These measures help to extend the service life of the floor heating pipe. The novel "Ten Years of Death" is equally exciting. Everyone is welcome to click and read it!

There may be the following reasons for the return of water from the rainwater pipe: 1. [** Blocked pipes **: This is a common reason.] If there were debris and dirt accumulated in the pipe, causing the inner diameter of the pipe to become smaller and the water flow to be blocked, it might cause water to reverse. For example, if too much leaves and sand accumulated in the pipeline, the sewage and rainwater would not be able to be discharged smoothly and would turn against the water. 2. ** Poor hydraulic conditions **: The drainage of residential buildings is generally gravity drainage. The sewage and rainwater are first discharged into the drainage vertical pipe by the sanitary ware of the residential building, and then into the horizontal drainage pipe. If the hydraulic conditions in the drainage process are not good, it may cause water reversal. 3. ** Tubular problems **: If the quality of the pipe is poor, such as the inner wall is rough, it is easy to hang dirt, or the anti-corrosion pipe is not well prepared, it will cause poor drainage and lead to water reversal. 4. ** The pipe diameter is too small **: When the pipe diameter cannot meet the flow demand of sewage and rainwater, the water flow cannot be discharged in time, and it is easy to cause water reversal. 5. ** Settlement of houses **: The slope of the horizontal drainage pipe during residential construction generally meets the standard slope. However, if the settlement of the house is too large, it will affect the slope of the pipe, causing the flow rate of sewage and rainwater in the pipe to be unable to reach the self-cleaning flow rate, resulting in poor drainage. <a href="/?from=ask_words" style="color:red" target="_blank">Read more exciting novels for free</a>

I'm not too sure what's going on when you suddenly said "anti-pollution in the sewers on the third floor". Generally speaking, it could be that the main pipe downstairs was blocked, and the sewage could not be discharged, so it came up from the third floor. It could also be that there was a problem with the sewer pipe on the third floor, such as something falling in and blocking it, or the pipe was broken, the interface was not connected properly, and so on. You can first check if there are any foreign objects blocking the sewer on the third floor. If there are no foreign objects, then you may have to find a property manager or a professional pipeline maintenance staff to check the main pipeline. <a href="/?from=ask_words" style="color:red" target="_blank">Read more exciting novels for free</a>

The following are some solutions to the problem of water flooding on the first floor during heavy rain: 1. * * Mount the check valve ** - Principle: The check valve relies on the flow of the medium and the force to open and close automatically to prevent the medium from flowing backward. When the water in the pipeline is reversed, the valve will automatically close to prevent the water from flowing back. It belonged to the automatic valve category and was mainly used for one-way flow of the medium in the pipeline. - Main points of installation: The check valve should be installed horizontally. Pay attention to the direction of the arrow on the valve body representing the direction of water flow, and the side with the valve cover should face up. During installation, leave enough space. According to the installation drawing or video, first install the ball valve, then install the check valve, and finally install the loose joint. The horizontal pipe can save an elbow and a short pipe to directly connect the ball valve. After piecing it together, take it to the place where the water flows and compare it with the water. After that, apply the glue evenly on the contact surface of the pipe. After applying the glue, it must be dried for 4 hours before it can be used. Also, try to avoid the installation during the peak period of water consumption. 2. * * Use chemical or physical methods ** - Use corrosive soda or pipe dredge to clear the pipe. These substances can dissolve or break down the material that causes the blockage. - Use a pipe dredge to clean up the impurities in the pipe and remove the blockages through mechanical action. - Use a high-pressure water gun to clean up the oil stains attached to the pipeline, and use the impact of the high-pressure water flow to restore the pipeline. 3. * * Check the outdoor main pipe and contact the property management ** - If there was no problem with the pipes at home, it might be the main pipe outside that was blocked, causing the water to flow back. This situation needed to be solved by contacting the property management. 4. * * Cultivate good drainage habits (preventive measures can also help to alleviate the situation)** - Don't throw all the garbage into the waterway. For example, first clean the bones, fishbones, and other residue into the trash can, then wipe the grease in the plate with a tissue and wash it with warm water to prevent the grease from flowing into the water and attaching to the pipe wall. - For the bathroom sewer, when washing your hair and bathing, you should prevent hair from flowing into the sewer and clean the hair on the floor drain in time. - When using water in the kitchen or bathroom, you can use a container to fill the water. After using it, you can drain the water in one go. This will form a force that can wash away the dirt on the sewer wall. - In the winter, you can pour boiling water into the water pipe regularly to wash the oil stains attached to the water pipe wall. However, if the sewer pipe at home is relatively thin, be careful not to use too high temperature boiling water to avoid causing the sewer to be deformed. <a href="/?from=ask_words" style="color:red" target="_blank">Read more exciting novels for free</a>

There could be many reasons for the blockage of the drainage pipe and the water on the third floor could be reversed, and different solutions could be taken. ** I. Cause Analysis ** 1. ** Congestion ** - Hair, kitchen waste (rice, vegetable leaves, noodles, etc.), grease (such as lard), and other sundries may have accumulated in the pipeline, causing poor drainage and water flow to fail smoothly, resulting in water reversal on the third floor. - It could be that the pipes at the lower levels were blocked, such as the pipes below the second floor, causing the water above the third floor to be unable to drain normally and turn against the water. 2. ** In terms of installation ** - If the drainage pipes on the third floor were not installed reasonably, such as the installation position of the drainage hose being too low, it would make it easy for water to accumulate and not be discharged in time, causing water to reverse. ** 2. Solution ** 1. ** Temporary measures ** - A sealing ring could be placed at the drain outlet of the reverse water. This would fix the sewer pipe and block the gap between the hose and the sewer pipe. To a certain extent, it would reduce the reverse water situation. Even if the water flow was fast, it was not easy for the water to return from the drain. 2. ** Clear the blockage ** - ** Chemistry ** - He could use the vinegar and soda method to first drain the water in the sewer, then mix the white vinegar and soda powder, and then add hot water into the sewer to use a chemical reaction to dissolve the blockage. - The salt and soda method was also feasible. Mix 1/2 cup of salt and 1/2 cup of soda water and pour them into the sewer. This mixture would help remove the dirt on the inner wall of the pipe, expand the diameter of the pipe, and dredge the pipe. - You can also use a pipe dredge agent. According to the instructions, you usually add an appropriate amount of dredge agent and warm water (no more than 60 degrees) to make it react in the pipe and dissolve the blockage, such as hair, meat, vegetable leaves, etc. - ** Physical method ** - Using the hot water method, boiling hot water was poured into a kettle or pot, and a towel was used to block the sewer to maintain the temperature and pressure of the hot water. The flushing and softening effect of the hot water was used to dredge the pipe. - The pump method could also be tried. First, the mouth of the sewer was blocked, and fresh water was poured in. Then, the pump was continuously pumped, and through the up and down circulation, pressure was formed. The external water pressure was used to dredge the sewer, but this method was more cumbersome. - The mop method. If the blockage was urgent, the mop could be used to directly block the drain, creating pressure back and forth. Repeat 5 - 10 times to discharge the blockage. - The mineral water bottle method was to cut off the bottom of the mineral water bottle, put on gloves, and insert the mineral water bottle vertically into the sewer. Repeatedly lift and press down, and discharge the foreign matter in the sewer through the huge pressure formed in the bottle. If the toilet was blocked and the bottle was not high enough, the insulation tape could be used to stick the 502 to the disposable chopsticks and the bottle cap firmly before continuing the operation. After dredging, he had to use half a bowl of white vinegar, five pump of dishwashing liquid, and three spoonfuls of baking soda mixed with boiling water to pour it into the sewer for deep cleaning to prevent secondary blockage. 3. ** Protective measures ** - When installing the pipe, whether it was the sewer pipe of the vegetable basin or the pipe under the bathroom cabinet, it must be higher than the ground. At the same time, the water hose should be plugged in to help prevent water from flowing back. <a href="/?from=ask_words" style="color:red" target="_blank">Read more exciting novels for free</a>

The sewer on the first floor could be flooded for the following reasons: 1. Damped or frozen pipes: The first floor is prone to moisture. Under certain circumstances, the pipes may freeze (such as when the temperature is low and the occupation rate is low), which will affect the discharge of water and lead to water reversal. 2. Blocked pipe: - Falling into a foreign object or a mistake in the installation of a new pipe could cause a blockage. - After the sewer pipe was used, it would scale up, causing the inner diameter of the pipe to become thinner and affecting the discharge of the sewage. - The main pipe was blocked. The main sewers on the first to seventh floors were more likely to be blocked. The blocked position was usually at the 90-degree turn from the sewer cover to the first floor. - Upstairs residents threw large objects that were not easy to decompose into the toilet, such as sanitary napkins, big bones, etc., which might block the part connecting the sewage well and the thick horizontal pipe, or corrode the pipe and make its diameter thinner, which would cause the water on the first floor to reverse. 3. The problem with the drainage system: If the floor drain returns water, it may be that the drainage pipe is not smooth, and the sewage will flow back to the floor drain closest to the blockage point. <a href="/?from=ask_words" style="color:red" target="_blank">Read more exciting novels for free</a>

The floor drain was overflowing because the water pipe was blocked. How should he deal with it? First of all, you can try using a leather spatula, which is the kind of thing that looks like a bowl. You can aim it at the drain and press it hard. After a few times, you can sometimes open the blocked thing. If the leather handle didn't work, you could find a wire, bend it, and put it into the floor drain pipe to hook the hair and debris that were blocked. There was also a chemical method, which was to use a pipe dredge. According to the instructions, the dredge was poured into the floor drain. After a while, it would break down the dirty things and then rinse them with water. If these methods did not work, then they might have to find a professional pipeline dredge. <a href="/?from=ask_words" style="color:red" target="_blank">Read more exciting novels for free</a>

If the floor drain pipe is blocked and the water is reversed, the following treatment methods can be taken: 1. ** Draining and dredging method **: First, flush the floor drain continuously, then choose the U-shaped iron wire to extend into the floor drain and rotate it continuously to rotate the blocked foreign matter down. Finally, flush it away with clean water. 2. ** Air pumping method **: Prepare a pump, put the rubber tube of the pump into the drain pipe of the floor drain, seal the surroundings of the floor drain, and then put enough water into it. Use this space to pump air into the floor drain to quickly clear the drain. 3. ** Vinegar and baking soda method **: First pour baking soda into a bowl, then add vinegar and a small amount of water. After mixing it, he poured it into the drain. After a while, the drain would clear itself. 4. Soda plus vinegar dredging method: pour half a cup of cooked soda into the blocked floor drain, then pour half a cup of vinegar. The soda and vinegar will react to remove the grease adhered to the pipe, thus clearing the pipe. 5. [Alkaline dredging method: Throw the kerosene into the sewer pipe and pour some hot water into the pipe. When the kerosene meets the hot water, it will undergo a chemical change, causing the temperature in the pipe to rise rapidly. The grease in the pipe will melt and be discharged with the water.] <a href="/?from=ask_words" style="color:red" target="_blank">Read more exciting novels for free</a>

This isn't related to online novels. However, if one wanted to deal with the problem of the floor drain of the balcony rainwater pipe, one could generally check if the pipe was blocked. If it was blocked, one could use a tool to dredge it. A pipe dredge was quite useful. If there was a problem with the drainage slope, he might have to adjust the slope. But I don't have any pictures of this. <a href="/?from=ask_words" style="color:red" target="_blank">Read more exciting novels for free</a>