Surveillance camera, night glass reflection, what's going on?
If the infrared camera has glass reflection at night, it may be caused by the following reasons: 1. Reflected light: The glass surface of the infrared camera may reflect surrounding light, especially at night or in the near-infrared spectrum. This reflected light could come from other lighting devices, the headlights of the vehicle, or other light sources. 2. [Normal phenomenon: Some infrared cameras have optical designs, so that light reflection at a certain angle is a normal phenomenon.] This design could improve the image quality and clarity of the camera to a certain extent. Read more exciting novels for free
How to deal with the strong reflection of the surveillance at night
Here are some ways to deal with the strong reflection of the surveillance at night: 1. ** Adjusting the camera angle **: Make the camera angle and the reflective light source (such as window glass) form a certain inclination to prevent the lens from facing the reflective light source. 2. ** Sticking anti-reflective film **: Sticking a special anti-reflective or low-reflective film on reflective surfaces (such as windows) to reduce the probability of light reflecting back to the camera. 3. ** Control the indoor light source **: adjust the indoor lighting equipment to reduce unnecessary internal light sources at night, or change the direction of the light source to prevent it from shining directly on objects that may cause reflection (such as windows). 4. ** Use Polarizing filter **: For cameras with changeable lenses or filter functions, you can install a Polarizing filter to reduce reflection. 5. ** Close to the glass (if the reflection is through the glass)**: Mount the camera as close to the clean glass as possible, but make sure that the lens does not touch the glass to avoid vibration and scratches. 6. ** Shrouding Method **: Use curtains, shades, and other items to block part of the window area to prevent external light from entering the lens. At the same time, ensure that it does not affect the monitoring of the required monitoring area. 7. ** Change installation position **: If possible, move the camera to a position that does not allow it to pass through reflective objects such as glass and directly face the monitored area. 8. ** Using infrared night vision technology optimization (for night vision cameras)**: To ensure that the infrared light source will not directly shine on reflective objects such as glass and cause reflection. Some of the cameras were designed with an infrared filter that could automatically switch to day and night mode during the day to reduce the reflection of visible light. 9. ** Choose a special night vision camera **: Choose a night vision camera that is designed for reflective problems and has anti-reflective capabilities. These products are usually combined with special coating or structural design to reduce reflective phenomena. <a href="/?from=ask_words" style="color:red" target="_blank">Read more exciting novels for free</a>
The smallest surveillance camera
The pinhole monitor was the smallest and most convenient monitor. It could be installed in a hidden place and was not easily discovered. If there was an internet connection, it could also be used for remote monitoring. In terms of size, the world's smallest SS-L1475 camera was about 4.4mm in diameter and 15mm in length. It could shoot 320x240-pixel-QVP video and had an LED flash at the top. In addition, there were some miniature monitors on the market that were less than the size of a jelly bean and could be easily placed in the palm of one's hand or hidden in other objects. However, these miniature monitors were usually used for security monitoring or spying. There was also a 12 * 12mm ultra-miniature color camera. Its appearance and workmanship were exquisite and beautiful. The wires were precise, and the structure was rigorous and reasonable. It was extremely convenient to install and use. It was small, flexible, and had low illumination. It could be carried around. <a href="/?from=ask_words" style="color:red" target="_blank">Read more exciting novels for free</a>
Surveillance camera manufacturer
The brands in the security surveillance camera industry mainly included Seiko, Tenglong, Computar, Fujineng, Tuli, and so on. In addition, there were also Hikvision, EZVI, Dahua, 360, KEDA, Philip, Samsung, D-Link, Ithink, Jooan, VStarcamera, Huamai, Datang Bodyguard, lenova, Huaxin, Anda, Shibojia, Tianshida, Aochman, Tiandi, Longse, Hengsi, Luowice, Transcendence, Watec, Gangqi, Zhongtian Lingzhi, Hongxiang, and other manufacturers. <a href="/?from=ask_words" style="color:red" target="_blank">Read more exciting novels for free</a>
Surveillance camera with a lens
The surveillance camera was just a single video capture device. The resolution and resolution of the lens were higher than that of the computer's video head, but it could not catch up with professional digital cameras or DVs. In reality, cameras and lenses were mostly purchased separately. The user can calculate the focal length of the lens according to the size of the target object and the distance between the camera and the object to determine the required lens. The lens required by each user depends on the actual situation. It cannot be assumed that the camera (head) already has a lens and does not need to be equipped with another lens. The focal length of the lens determined the field of view of the camera. For example, a wide-angle lens was suitable for shooting in a large space and could capture more content. A telephoto lens was suitable for long-distance shooting and could see details in the distance. Indoors, they usually chose short focal lenses, such as 2.8mm or 3.6mm lenses, while outdoors, they chose lenses based on distance. Moreover, different focal length lenses had different imaging effects. Long focal length lenses could see more details of distant objects, but the field of view became smaller and the viewing range became narrower. Wide-angle lenses had a wide viewing range, but it might be difficult to distinguish some details. <a href="/?from=ask_words" style="color:red" target="_blank">Read more exciting novels for free</a>
The surveillance camera on the highway?
The video surveillance on the highway might have a camera function. For example, the violation camera was generally spherical in shape. Its function was to capture and punish the captured vehicle. Many traffic accidents were caused by parking violation. This kind of camera was installed in the no-parking section, and it was also installed in the parking area of the highway bus. Electronic eyes were used to detect illegal behavior while driving, such as running red lights, changing lanes, etc. Although there was no explicit mention of taking photos, detecting these behaviors usually required taking photos for evidence. Therefore, there were video surveillance cameras on the highway. <a href="/?from=ask_words" style="color:red" target="_blank">Read more exciting novels for free</a>
Focus the surveillance camera
If it was a general non-integrated surveillance camera, the method of adjusting the focal length was as follows: First, remove the camera, check the small screw like parts at the lens and loosen it, then turn the circle on the lens to adjust the focal length. When adjusting the focal length, it was best to take it off and adjust it while facing the monitor screen. If it was inconvenient to take it off, two people were needed. One person looked at the screen and cooperated with gestures or words, and the other person adjusted it next to the camera to achieve the best effect. It could also be adjusted manually. Some surveillance cameras had two buttons that could be rotated. One was used to adjust the distance and the other was used to adjust the clarity. There was another adjustment method: first loosen the fixing screw of the camera's rear focal length adjustment ring; adjust the zoom lens to the maximum telephoto position, and use the focal length adjustment ring on the lens to set the focal length until the image is the clearest; then adjust the zoom lens to the maximum wide-angle position, and turn the rear focal length adjustment ring until the image is the clearest; when switching from telephoto to wide-angle, repeat the above two steps until the image is in focus; finally, after the setting is complete, tighten the rear focal length adjustment ring. In addition, he added a new experience of adjusting the lens. He loosened the screw that fixed the standard lens, adjusted the magnification, and adjusted the lens to a telephoto state. Then, he zoomed in on the distant object, and then adjusted the focal length to make the close-up image clear. Then, he pulled the lens back to the wide-angle state by zooming out. The image he just shot should be a panoramic view. Don't adjust the focal length of this panoramic view (even if the image is blurry, don't adjust it). Go straight to the next step, which is to adjust the back focal length to adjust the image to the best picture. Finally, tighten the small screw of the lens, and the back focal length adjustment is completed. <a href="/?from=ask_words" style="color:red" target="_blank">Read more exciting novels for free</a>
Surveillance camera 12mm
He only mentioned that the "surveillance camera 12mm" was rather vague and did not know the specific content of the problem. If it was a surveillance camera with a 12mm lens, from the reference, the surveillance camera with a 12mm lens could monitor a distance of 50 meters. For example, there was a 1200-line security equipment infrared night vision surveillance camera, and a high-definition array camera was a 12mm lens. The reference price was 388. Different focal lengths would affect the field of view of the camera. The 12mm lens was a telephoto lens, suitable for long-distance shooting and able to see details in the distance. However, it might not be suitable for indoor surveillance. Usually, 2.8mm or 3.6mm lenses were chosen indoors. If it was outdoor monitoring and needed to monitor a long distance, a 12mm lens could be considered. At the same time, when choosing a surveillance camera, in addition to the lens, it was necessary to consider the networking method, the resolution, the video storage method, indoor and outdoor use, the power supply method, the voice intercom, and many other factors. <a href="/?from=ask_words" style="color:red" target="_blank">Read more exciting novels for free</a>
What does the red dot on the surveillance camera mean at night?
The red dot on the surveillance camera at night meant that the camera was turned on. The red dot was an infrared LED. At present, the most commonly used infrared camera in surveillance engineering refers to active infrared, which is mainly emitted by the LED. The camera's CCD-based image is based on the infrared reflected by the object, and the market is mainly based on the infrared LED that emits 850Mm and 940Mm.
Surveillance camera accessories, dedicated surveillance cable for cameras
There were many types of surveillance wires in the surveillance camera accessories. For example, the monitoring accessories such as the Ego BMC to RV male cable, the video cable, and the BMC to LV cable were priced at 2.95 yuan. There was also Coffey's Android data cable that could be used as a camera power extension cable. There were different lengths of 2 meters, 3 meters, 5 meters, and 10 meters to choose from. The 5-meter-long Android ladder was suitable for mobile phones/surveillance cameras, etc. The Chao Fan was suitable for the Xiaomi camera power extension cable of 3 meters, which could be used for Fluorites, Le Orange, 360, Huawei, Little Ant, Xiaobai, Pulian TP-Link, Dahua cameras. There was also an outdoor power supply extension cable of 5 meters that could be used for the standard 2K outdoor battery of the Xiaomi 2 cloud platform version, the new version of the surveillance camera's Class-C charging cable, data cable, and so on. <a href="/?from=ask_words" style="color:red" target="_blank">Read more exciting novels for free</a>
Surveillance camera aperture means
In terms of concept, the aperture was a device in the surveillance camera that controlled the light passing through the lens and adjusted the light sensitivity inside the camera. In terms of structure, it was controlled by the amount of light passing through the lens. Usually, the F-value was used to express the size of the aperture. In daily life, 1.0, 1.2, or 1.4 would be used to represent the aperture size of the lens. When the F-value was smaller, the larger the aperture was, and the more light the sensor chip could pass through. <a href="/?from=ask_words" style="color:red" target="_blank">Read more exciting novels for free</a>