The two-dimensional measuring instrument cannot see the image.
If the two-dimensional measuring instrument cannot see the image (image imaging fails), you can check the power supply voltage and insert the signal cable into the display screen; if the parts are damaged, you need to replace the display or the crosshair generator; if the deviation between the crosshair and the tracking point is large when the objective lens is magnified, you need to readjust the screw locking the lens barrel or replace the lens barrel; if there is a shadow in the measured work piece, please adjust the screw on the four corners of the camera or glass. Read more exciting novels for free
2010 Dimensional Measuring Instrument
The 2D Measuring Instrument 2010 was as follows: 1. Equipment preparation: Turn on the computer, the two-dimensional measuring instrument, and other related equipment one by one, and click on the icon of the secondary measuring platform. Make sure that the appearance of the measuring instrument is not damaged, the components are intact, and the equipment is in normal working condition. At the same time, it was necessary to ensure that the measurement environment met the requirements of the measuring instrument, such as temperature, humidity, etc. 2. Placing the corrected version: Place the corrected version on the test bench with the character 2014 facing up. The corrected version should be placed horizontally on the test bench without any foreign objects blocking or tilting. 3. Lighting and camera adjustments: Find the circle on the correction board, turn off the LED light, adjust the lens resolution, and adjust the correction light (lower light); After clicking the image correction-three circles under the correction processing menu, move the three circles on the screen to the edge or inside of the reference circle. When you shake a dot, the left mouse button will show a blue circle (the reference circle should not leave the screen), and then click the right mouse button on the screen. The correction success and the zooming factor will appear. Then click OK, and then measure the reference circle. 4. Calibrating verification: After the completion of the measurement, the round hole on the standard part shall be measured. During the measurement, click the automatic capture of edge points and circle command, and then capture more than three points on the edge of the reference circle, click the right mouse button to draw a circle, and the size will be automatically generated. If the measured size are consistent with the standard size (tolerance: 0.005mm), the equipment is in good condition. On the contrary, if the tolerance is exceeded, the equipment may be abnormal. You should contact the auxiliary imaging instrument supplier in time. 5. Record data: After each verification, the examiner will record the amplification factor, verification time, verification and verification error value, so that the examiner can consider the error value during the actual inspection. In addition, the correct input of the ball diameter parameters of the two-dimensional image measuring instrument also had an impact on the measurement accuracy. During the operation, it was also necessary to ensure that the input was correct, and pay attention to whether the compensation file was correct. If it was incorrect or lost, the measurement accuracy of the two-dimensional image measuring instrument would be inaccurate and unreliable. It needed to be re-verified and installed to obtain the correct measurement value. <a href="/?from=ask_words" style="color:red" target="_blank">Read more exciting novels for free</a>
Requirements for the verification of the two-dimensional measuring instrument
The conditions for the verification of the 2D measuring instrument were as follows: 1. ** Appearance inspection ** - It was necessary to confirm that the two-dimensional workbench and the measurement reference plane were clean, and that the X and Y axes were unobstructed. - Confirm that the standard instrument is within the validity period of the calibration. There is no damage to the appearance that will affect the test results. 2. ** Calibrating environmental conditions ** - The temperature should be 20 - 25°C, and the humidity should be less than 70%. 3. ** Standard parts ** - Prepare 2D verification films and other standard parts. 4. ** Personnel ** - The personnel conducting the calibrations shall undergo an effective assessment and obtain corresponding qualification certificates. 5. ** In terms of tools for alignment ** - Prepare the necessary alignment tools, such as standard gauge blocks, standard wire gages, etc., to ensure the accuracy and reliability of the tools. <a href="/?from=ask_words" style="color:red" target="_blank">Read more exciting novels for free</a>
Beihai 2D Image Measuring Instrument Price
The price of the Beihai 2D Image Measuring Instrument was 43,000 yuan for one set, 37,000 yuan for two sets, and 11,600 yuan for three sets and above. <a href="/?from=ask_words" style="color:red" target="_blank">Read more exciting novels for free</a>
Xuzhou three-dimensional coordinate measuring instrument quote market
There was no fixed price for the coordinate measuring machine, and it would be affected by many factors, such as brand, model, configuration, etc. No special information related to the quoted price of Xuzhou's three-dimensional coordinate measuring machine could be found, so it was impossible to accurately provide its quoted price. <a href="/?from=ask_words" style="color:red" target="_blank">Read more exciting novels for free</a>
p Photographic measuring instrument
Photographic measuring instruments were divided into three-dimensional measuring instruments and ground three-dimensional measuring instruments. The three-dimensional measuring instrument is an instrument used in the differential method of aerial photography. It uses a correcting machine to eliminate the influence of photo tilt and aerial height difference on the measurement of height difference between ground points. The ground three-dimensional measuring instrument was one of the instruments used in ground three-dimensional photogrammetry. After the photographic image pair was oriented on the instrument, it could be used for three-dimensional observation. Through the transmission mechanism, it could automatically draw the ground features and contours on the drawing table. This kind of instrument could only deal with upright photography and equal-tilt photography. If equipped with a "tilt calculator", it could also deal with equal-tilt photography. <a href="/?from=ask_words" style="color:red" target="_blank">Read more exciting novels for free</a>
Speckle measuring instrument photography
Different speckles had different requirements and characteristics. For example, when the seventh generation of Visia was tested, it would test the left, right, and left sides and then take photos. During the test, it was not allowed to apply any sun protection or makeup, and it had to be cleaned before the test. When the AI intelligent skin detector was used, it would take photos in different directions according to the prompts, and it needed to remove makeup before the test. There were other related devices on the market, such as smart skin detection and freckle removal devices, but there was no mention of special requirements for photography. <a href="/?from=ask_words" style="color:red" target="_blank">Read more exciting novels for free</a>
Model and specifications of the 2D measuring instrument
There were many models and specifications of the two-dimensional measuring instrument. For example, the VM3020 in the VVS series had a measuring stroke of 300*200, a magnifying power of 280X, an automatic mouse control mode, a measuring accuracy of +/-0.003, an overall size (length * width * height) of 670 * 600 * 900 (mm), and a resolution of 0.001. There were also models and specifications such as QC3020T, QC4030T, QC5040T, etc. In terms of measurement range, X(mm) was 300, 400, 500, Y(mm) was 200, 300, 400, Z(mm) was 200, 200, 200, and the marble countertop size (mm) of the workbench was 460*360, 560*460, 710*610. The size of the glass countertops (mm) were 329*229, 429*329, and 529*429 respectively; the weights of the instruments (kg) were 200, 280, and 380 respectively; and the outer shapes (mm) were 760*660 * 970, 860*760*970, and 1160*910*1020 respectively. <a href="/?from=ask_words" style="color:red" target="_blank">Read more exciting novels for free</a>
Single-phase intelligent digital display voltage measuring instrument
The single-phase intelligent digital display voltage measuring instrument is an advanced electric quantity display instrument. It can be used together with a mutual sensor, voltage splitter, etc. to realize the digital display of voltage and other parameters in the power grid. This type of instrument uses advanced measurement technology and high-quality components. It has the advantages of high precision, strong isolation, stable performance, and easy installation. Compared with traditional measuring devices, it had obvious advantages in terms of measurement accuracy, response speed, anti-interference ability, and so on. In terms of display, it uses a large screen liquid crystal display or a row of LED digital tube display, which can display voltage and other power parameters at the same time. It can also switch the display content easily by pressing the button, and send out an alarm for abnormal situations. The instrument has a variety of communication agreements, which can be connected to computers, Plcs and other equipment to achieve remote monitoring and data acquisition. It also has the function of RS485 communication and uses the MODBU-Rtu protocol to make the data transmission stable and reliable. Some products also have two switch input and output, as well as one circuit of the output, allowing the user to control and monitor the power system more flexibly. To expand the measurement range, it was only necessary to equip the corresponding current or voltage transformer, and the input parameters could be programmed on the spot. <a href="/?from=ask_words" style="color:red" target="_blank">Read more exciting novels for free</a>
The image of a character that cannot be used
Quan Wuyong was a character in The Scholars. He was a self-proclaimed celebrity, recommended by Yang Zhizhong, praised for his world-shaking talent and unprecedented knowledge. However, the people of Xiao Shan that he met on Huan Cheng's boat had a negative evaluation of him, and he was a person who repeatedly failed his exams. During the mourning period, he refused to personally go to the Lou Mansion. His experience in the Lou Mansion and Yang Zhizhong's evaluation of him changed from the initial recommendation to privately calling him a madman. He seemed to be a celebrity, but in fact, he did not live up to his name. Combining all these aspects, it revealed a complex and ironic character image. The novel " Don't Consume My Identity " is equally exciting. Everyone is welcome to click and read it!
Which is the best two-dimensional video instrument in Shannan
In the Shannan Prefecture, Spitec's 2D imaging device had a certain advantage. Since its establishment 16 years ago, Spitec has been committed to the research and development of image technology and machine vision. It has more than 70 senior researchers and industrial engineers in machine vision systems. Its two-dimensional imaging instrument had various functions, such as Shannan Super Two-Dimensional Measuring Instrument, Shannan Image Measuring Instrument, etc. All of them had the function of quickly detecting the size of multiple products with one button (1 second), the accuracy could reach 0.003mm, and it could directly display the functions of good and bad products. Shannan One-button Detector could also check length, height, diameter, mixing, distortion, lack of materials, barbs, black spots, scratches, etc. The scope of application included rubber rings, screws, etc. <a href="/?from=ask_words" style="color:red" target="_blank">Read more exciting novels for free</a>