Jewelry DSLR parameters
Take the Canon 500D jewelry as an example (Canon 500D is an APS-C format single-lens reflex). If you use a 35mm f2.8 fixed-focus lens, the shutter speed can be guaranteed to be 1/35, and the aperture can be contracted to about f4. This can make the aperture reach the best state, ensure the sharpness of the focal point, and achieve a certain background blurring effect. The lowest sensitivity is 100 or lower to ensure the best picture quality. Then, the light is used to assist the exposure parameters to achieve accuracy. Read more exciting novels for free
DSLR macro parameters
The following are some of the key parameters for DSLR macro photography: 1. ** Scene Selection **: - Common macro lenses had focal lengths of 50mm, 60mm, 90mm, 105mm, and 200mm. - Short focal length lenses below 70mm had a shorter focusing distance, suitable for shooting still life details; macro lenses above 100mm were suitable for shooting moving objects such as insects because they could be farther away from the subject and reduce interference;70 - 100mm focal length was between the two, covering both static and dynamic scenes. 2. ** Aperture **: - Unlike daily shooting where a large aperture was used to create a small depth of field, macro photography often chose a smaller aperture, such as F8 - F11, or sometimes even F16, because the depth of field of the macro lens was shallow and the depth of field would decrease when the lens was close to the subject (there was a background blurring effect). However, there were also cases where F2.8 - F4 was used to create a background blurring effect to highlight the main part of the macro. 3. ** Shutter: - When shooting agile objects such as insects, a high shutter speed, such as 1/250, was needed to capture the moment. Moreover, when not using a tripod (it is more troublesome to set up a tripod when taking a photo), the slight shake of the hand will affect the clarity of the macro photography, and a higher shutter speed will help the clarity of the shot. 4. ** Replenishing Light **: - In macro photography, a small aperture (less light per unit of time) and a high shutter (less light per unit of time) were often set. Forcefully raising the IQ would affect the image quality and produce high noise, so it was necessary to fill in the light appropriately. Although it was simple to use a flash, the light was too strong. The contrast and brightness of the object were too obvious. A better method was to choose to use a diffusing device or a miniature reflective plate to fill in the light for the main body. 5. ** Other shooting modes and parameters **: - When shooting small things such as flowers, birds, and insects, you can use the Av file. The aperture is best to be f5.6 or larger, and the focal length is above 50mm. Try to shoot within 1 meter to achieve background blurring. <a href="/?from=ask_words" style="color:red" target="_blank">Read more exciting novels for free</a>
Huahai DSLR parameters
If you were to use a single-lens reflex camera to shoot the sea of flowers, you would need to consider the following parameters: 1. ** Choice of lens **: If you want to shoot a large area of colorful flowers, you usually need to use a wide-angle lens; if you want to shoot the details of a flower at a close distance, you can use a telephoto lens, and it is best to use a macro lens. This can achieve the ideal definition and make the details of the subject clear, which is not available in ordinary lenses. 2. ** Aperture Setting **: Aperture can be adjusted according to your needs. For example, if you want to blur the background and highlight the main body of the sea of flowers, you can increase the aperture; if you want to make the whole sea of flowers appear clearly, you need to adjust the aperture size according to the actual situation. 3. ** Focus **: If you are shooting a large scene, autofocus is usually fine. However, if you are shooting a close-up close to the flower, autofocus may not work well. You can switch the AF-autofocus on the lens to MTF-manual focus, and then turn the focus ring to focus. 4. ** Photometering **: Generally, you can choose average dimming, which will take into account the exposure of the subject and the background at the same time. However, if the flower is light-colored and the surrounding is dark-colored, using this dimming method may cause the flower bud to be overexposed. In this case, you can use partial dimming or spot dimming. Spot Metering would consider the exposure of the main body and its surroundings, but the main body had a higher weight. Spot Metering only considered the exposure of the main body, and could be applied flexibly according to the actual situation. <a href="/?from=ask_words" style="color:red" target="_blank">Read more exciting novels for free</a>
DSLR exposure parameters
The exposure parameters of an DSLR mainly included the following aspects: 1. ** exposure compensation **: Expressed in the word 'EV', it is an exposure control method to further adjust the brightness of the photo. If the environment is dark (the photo taken is dark), you can increase the exposure value (the scale line on the display screen moves to the right, which is the positive direction), and the photo will be brighter than when the EV is 0; otherwise, it will be darker. 2. ** Flash compensation **: Also indicated by the SUV value. The brightness of the photo can be changed by changing the brightness of the camera's built-in flash. It is generally used to fill in the light for people in portrait photos. 3. ** The three elements of exposure **: - ** Aperture **: Aperture size affects the amount of light entering and depth of field effect. If the aperture was opened wide, the exposure would increase and the background would blur; if the aperture was closed, the exposure would decrease and the background would be clear. For example, if you need a shallow depth of field (background blur) effect for portraits, you can choose an aperture value of f/2.8 or higher. - ** Shutter Speed **: Slow down the shutter speed to increase the exposure, allowing for a slow-motion effect; fast up the shutter speed to reduce the exposure, making it suitable for shooting moving objects. - ** Light sensitivity (USB)**: Increase the sensitivity, increase the exposure, but increase the noise; decrease the sensitivity, reduce the exposure, and improve the image quality. On sunny days, the outdoor CPU can be set to 100 - 400; on cloudy days or indoor natural light, it can be set to 400 - 1600; at night or in low light, it can be set to 1600 or above, depending on the required shutter speed and acceptable noise level. 4. ** Reciprocity Law **: When the exposure is determined, adjust one of the exposure parameters to increase or decrease the exposure. The other two parameters must be adjusted accordingly to reduce or increase the exposure to maintain the same exposure. For example, if the aperture was F4, the shutter speed was 1/60 seconds, and the sensitivity was 800, then if the aperture was increased by 3 stops to F1.4 (the exposure increased by 3 stops), the shutter speed could be increased by 3 stops to 1/500 seconds or the sensitivity could be lowered by 3 stops to 100 to maintain the exposure. 5. ** White Balance (AWB)**: This is the default setting for the white precision generated after changing the three primary colors of red, green, and blue in the environment. AWB is the default setting of the camera. 6. ** Automatic brightness optimization **: The camera automatically processes photos. 7. ** Metering mode **: There are four types of measurement: evaluation, spot, spot, and center weight average. <a href="/?from=ask_words" style="color:red" target="_blank">Read more exciting novels for free</a>
Basic parameters of DSLR
The following are the basic settings for common DSLR scenes: ** 1. Portrait Shooting ** 1. ** Still Portrait ** - Shooting mode: Aperture priority mode (LV) can be selected, and the aperture is set to a large aperture, such as F2.8 or larger. - Focus: Focus on the person's eyes. - [Light sensitivity: Daytime light sensitivity can be set between 100 - 400.] - [Focus: Use a focal length of 50mm or above.] - [Shooting distance: Depends on full-body, half-body, and headshot.] 2. ** Portrait in motion ** - [Shooting mode: Shutter priority mode (TV), shutter speed set to 1/250s.] ** 2. Scenery Shooting ** 1. ** Ordinary scenery ** - Shooting mode: You can use P or Aperture priority mode, and the aperture is set to F5.6 or smaller. - [Shot: It is recommended to use a wide-angle lens to accommodate more scenery.] - [Light sensitivity: For example, the clear day's light sensitivity can be set to 100, and the cloudy day's light sensitivity can be set to around 400.] - "Picture composition: avoid placing the most attractive scenery in the middle of the picture. You can use the three-point composition, frame composition, symmetrical composition, diagonal composition, white space composition, etc. 2. ** Special parameters (M file) Shooting on a sunny day ** - It had a shutter speed of about 1/200, and a cloudy day with a shutter speed of 400. ** 3. Flower Shooting ** - [Shooting mode: Aperture priority mode (LV)] - "Lenses: You can choose a large aperture lens or a 100-micro lens. The aperture should be large to highlight the main body and make the depth of field shallow, making the picture softer. - [Composing: You can use the central composition or the nine-square composition to place the main body in the center of the picture.] ** 4. Pet Shooting ** 1. ** Method 1 ** - [Shooting mode: P-grade automatic, continuous shooting function activated.] 2. ** Method 2 ** - [Shooting mode: Shutter priority mode (TV). Shutter set at 1/200s or higher.] ** 5. Night Scene Shooting ** - [Shooting mode: Aperture priority mode. Use a small aperture, such as F10 or smaller.] - [Light sensitivity: Normally set to 100.] - Shutter speed: Can be set to 1/30s. - Metering mode: Set it to the evaluation mode (Matrix Metering mode) and reduce the exposure compensation as appropriate. - [Ancestors: With the help of a tripod, you can use the shutter release to shoot.] ** 6. Silhouette Shooting ** - [Shooting Mode: P-file] - Metering: Use spot photography to measure the brightness of the light. Then, add or subtract the exposure according to the actual needs. Place the focus on the bright spot to measure the brightness. The dark part will become a black silhouette. ** 7. Shooting of still small things like flowers, birds, and insects ** - Shooting mode: Aperture priority mode (LV), the aperture is best to be f5.6 or larger. - [Focus: 50mm and above.] - [Shooting distance: Try to shoot within 1 meter, to blur the background.] ** 8. Portrait Shooting at Night ** - [Shooting mode: Aperture priority mode, f8 aperture.] - Light sensitivity: 100 - 400. - "Anciliaries: Use a tripod, set up automatic or custom white balance, and use slow sync flash (the flash flashes once when the shutter is pressed, and flashes again before the end of the exposure. You can't leave when you're shooting). ** 9. Shooting of moving objects ** 1. ** Method 1 ** - When the light is good, use Aperture priority mode (UA). A small aperture below f8 can get a large depth of field; a shallow depth of field can be obtained above f8, and continuous shutter can be selected. 2. ** Method 2 ** - If you want a dynamic effect, use the shutter priority mode (TV), set the shutter to about 1/30, focus, press the shutter, and at the same time, the lens will follow the target at an appropriate speed. In addition, you also need to pay attention to the photo size, format, and image quality settings. In special scenes, you may need to customize the white balance, set the shooting style, choose the appropriate focus mode, and the basic settings such as sensitivity (you can also directly set the sensitivity to the STAR position and let the camera adjust according to the scene) and exposure mode (M, aperture priority, shutter priority). <a href="/?from=ask_words" style="color:red" target="_blank">Read more exciting novels for free</a>
DSLR dimming parameters
According to the available information, the dimming parameters of the Silver Swallow SY-28As flash for the Sony-grade single-lens reflex were mentioned. The flash control had two automatic apertures, F2.8 and F5.6, and the flash index was 28 (100, 50mm focal length). However, this was only the dimming parameters of the specific flash. Generally speaking, the dimming of an DSLR camera was related to parameters such as aperture, shutter speed, and sensitivity. The aperture size directly affected the amount of light entering. A large aperture would enter more light, and a small aperture would enter less. A slow shutter speed would allow the light to enter longer, and a fast shutter speed would allow the light to enter shorter. The higher the sensitivity value, the more sensitive the camera was to light. However, high sensitivity might bring about an increase in noise. Under different shooting scenes and needs, these parameters needed to be adjusted to achieve the appropriate dimming effect. For example, when shooting portraits, a larger aperture (such as F1.8 - F5.6) may be used to obtain a shallow depth of field to highlight the main body of the character, but pay attention to the accuracy of the focus to avoid losing details; when shooting scenery, a small aperture (such as F8 - F16) may be used to ensure a larger depth of field to make the whole picture clear. <a href="/?from=ask_words" style="color:red" target="_blank">Read more exciting novels for free</a>
DSLR English parameters
The following are some common English parameters for DSLR: 1. ** Metering Mode **: It can be divided into Spot Metering, Matrix Metering, and Center -weighed Metering. 2. ** Iso-Mode **: Iso-is the sensitivity (International Standard Organization). The value can be adjusted. 3. ** Shutter Speed Mode **: S represents Shutter Speed. 4. ** Exposure-Value Mode **: Exposure-Value means exposure compensation. 5. ** AF-mode (auto-focus Mode)**: This is the auto-focus mode, which can be divided into active and passive modes. 6. **AWB Mode **: White Balance Mode. 7. Aperture: The English name is Aperture. The F value is often used to indicate the size and is used to control the amount of light entering. 8. ** NEP (RAW)**: An image format, 12-bit or 14-bit, can be compressed or compressed without loss. 9. **JPEG**: Common image format, fine (approx. 1:4), average (approximate. 1:8), basic (approximate. 1:16) compression. 10. DFC (Design Rule for Camera file system): 11. **Exif (Exchangeable Image File Format for Digital Still Cameras)**: Exchangeable image file format (for digital cameras). <a href="/?from=ask_words" style="color:red" target="_blank">Read more exciting novels for free</a>
DSLR party parameters setting
If the party was filmed without a lamp: - ** static characters and scenery (suitable for on-stage speeches, guest check-in, group photos, communication, and other scenes with small movements)**: - [Mode: M mode] - [Shutter: 1/60 second.] - Aperture: F4 - F5.6. - <strong></strong>Because in this scene, the shutter did not need to be too high, and if the light was bright, the USB could be turned on automatically, and the aperture was above F4 to ensure the clarity of the person in the photo. - ** Dynamic Character Scenery (suitable for programs, dances, lottery draws, awards, toasts, and other scenes with strong interaction)**: - [Mode: M mode] - [Shutter: Set to 1/125 - 1/160 seconds. If necessary, it can be increased to 1/200 seconds.] - Aperture: F4 - F5.6. - <strong></strong>Everything was done to capture the main character clearly. As it was a dynamic scene, the shutter speed could not be too slow, and the USB had to be controlled below 3200. In addition, if there was a stage electronic screen in the party scene, since the output frequency of the electronic screen was about 50 Hertz, in order to avoid the appearance of blurred screens and shadows when shooting non-continuous images, you could use a speed of about 1/50 second, speed priority mode, and the sensitivity setting to automatically shoot. <a href="/?from=ask_words" style="color:red" target="_blank">Read more exciting novels for free</a>
The meaning of various parameters of the DSLR
The following are the meanings of the common parameters of the DSLR: 1. ** AF-ON **: It is related to the focus mode. It can be set to switch between single-shot focus, autofocus, and servo-autofocus. By clicking the AF-ON button, and then clicking the menu button (MENU), you can directly use the AF-ON button to select the focus mode. 2. ** Depth-of-field button **: Can be set to the photo style. In the MENU, press a specific step to find the custom button, and then set the depth of field to the photo style, which can be used to choose whether to shoot portrait or landscape. 3. ** M-GN **: Can be set to drive mode, focus mode, white balance, light measurement mode, etc. Find the custom button in the MENU settings, click M-mn, and select the ticked item in the details. When shooting, click M-mn to switch the settings. 4. ** Image confirmation **: After taking a photo, the photo will stay on the camera for a period of time to check the effect of the photo. You can set the dwell time in the image confirmation option under the menu on the second layer of the first camera setting on the first layer. Generally, you can choose 2 seconds. 5. ** Light sensitivity (Isox)**: The sensitivity of the light sensor to light. The higher the USB, the more sensitive the sensor was to light, and the brighter the image would be if there was more exposure, or the darker the image would be. You can set a minimum and maximum value. The best image that the equipment can bear has a maximum value. If you exceed this value, the noise in the photo will increase. In the MENU setting, the first layer was the left camera setting. He clicked on the 2 option to set the sensitivity of the camera. After entering the sensitivity setting menu, he chose the automatic range and set the maximum and minimum values according to the range that the device could bear. 6. ** lens aberrations correction **: - [** Surrounding Light Rectification **: When turned on, dark corners can be reduced.] - ** Distortion correction **: When turned on, it helps to correct the image distortion. - ** Digital lens optimization **: You can choose the standard. The setting steps were to set the camera settings on the first layer of the MENU. In option 3, click on the lens phase difference correction, set the surrounding light correction to- on, distortion correction- on, digital lens optimization-standard. 7. ** High Iso-noise reduction **: In extremely dark environments, when there is no light or tripod and the exposure time cannot be extended, you can set this function to adjust the brightness of the screen, but it is not a long-term solution. In the MENU settings, the first camera setting on the left, click on the high iso sensitivity noise reduction function in option 4, and you can choose strong. 8. ** Shutter Release Without Memory Card **: If the option is not closed, the shutter can be pressed without a memory card. If the option is closed, the shutter cannot be pressed without a memory card. In the MENU settings, the first layer was the left camera setting. In option 6, click on the uninstalled memory card to release the shutter and choose off. 9. ** Gridline **: It is the reference line for composition. It is recommended to turn it on to facilitate composition. In the MENU setting, the first camera setting on the left of the first layer, click on the shooting information display-show grid line-3x3 grid line in option 7, and a "jing" line will appear on the camera display screen. 10. ** Aperture **: Generally indicated by F, it is mainly used to control the amount of light in the lens. Increasing the aperture by one, the amount of light entering the camera doubled, and vice versa. 11. ** Shutter **: It is used to control the length of exposure time. It is divided into high-speed shutter and slow shutter. The faster the speed, the darker the image. The slower the speed, the brighter the image. 12. ** Depth-of-field **: The distance from clarity to blurriness in the image. It is related to the aperture. The smaller the aperture, the greater the depth-of-field. The larger the aperture, the smaller the depth-of-field. The focal length of the lens also affects the depth-of-field. The longer the focal length of the lens, the smaller the depth-of-field. 13. ** focal length **:(mm) Usually marked in front of the lens, for example: 50mm/24 - 70mm, different focal lengths will affect the image. 14. ** exposure **: refers to the brightness of the photo. You need to adjust the camera parameters such as shutter, aperture, USB, exposure compensation, etc. to control the exposure of the photo. 15. ** RV **: It refers to the exposure index of the camera. The amount of exposure can be achieved through different shutter and aperture combinations. 16. ** Color temperature (K)**: Mainly used to adjust the color of the photo. Generally, the color temperature of natural light is around 4500K. The higher the value, the cooler the photo. 17. ** Automatic Focus Mode **: - ** Single autofocus (AF-S)**: It is used to focus on a stationary object. - ** Continuous autofocus (AF-C)**: Used to continuously focus on moving objects. - ** Automatic Focus (AF-A)**: An autofocus mode. 18. ** Focus area **: The use of the focus point must be used in conjunction with the measuring mode. There are a variety of focus points to choose from. The camera default is the center focus point. The user can choose the appropriate focus point according to the shooting needs. 19. ** Picture Style **: This is equivalent to the default settings for brightness, contrast, saturation, and other parameters. It reduces the number of post-processing steps and is similar to the filter in a mobile phone. 20. ** White Balance (AWB)**: It is the balance of white. It is the default setting for the accuracy of the white color generated after changing the three primary colors of red, green, and blue in the environment. AWB is the default setting of the camera. 21. ** Automatic brightness optimization **: The camera automatically processes photos. 22. **OS ON/OFF (anti-shake switch)**: The anti-shake function can compensate for shaking. Different brands have different names, such as Canon's IS. When shooting with a hand-held camera, the anti-shake function of the safety shutter could be increased by about 3 stops. 23. ** AF-M (autofocus and manual focus)**: Normally, the autofocus mode is set to AF-M. When the camera cannot autofocus accurately (such as when the light is dim at night and the contrast is low in the snow in winter) or when it is necessary to deliberately use manual focus to create a blurry effect (such as shooting at night), the manual focus mode can be switched to M-M. 24. **0.39m/1.3ft (closest focus distance)**: It means that the camera cannot focus when the distance between the camera and the subject is less than this value (39cm or 1.3ft). <a href="/?from=ask_words" style="color:red" target="_blank">Read more exciting novels for free</a>
DSLR character photo parameters
When shooting a DSLR portrait, the parameters would vary depending on the shooting situation. If you want to shoot a close-up of a person, you can refer to still life shooting. Set the sharpness to moderate, pay attention to the eyes or important parts of the person, and use the middle composition. If you want to shoot a portrait outdoors, the shutter speed can be set to 1/100s, Iso100, aperture F1.2 - 2.8. For indoor portraits, the shutter speed can be set to 1/80s, Iso1500, aperture F2.8 or less. When shooting people in motion, using aperture priority mode (audio file) may not meet the requirements. In this case, you can use shutter priority mode (TV file), and the shutter speed is set to about 1/250s. This way, it is not easy to make the photo blurry. If you want to shoot a person with a background, use a medium aperture F8 to highlight the background and the character. The focal length is the widest. The composition can be based on the three-point method or the golden section method. The lowest possible setting of the USB is 100. Save it in the RAW format. Pay attention to the correct exposure of the face. The color of the character's clothing should be different from the background. If the other parts are too black or overexposed due to insufficient tolerance, you can pull it back through the curve later. <a href="/?from=ask_words" style="color:red" target="_blank">Read more exciting novels for free</a>
Sony DSLR lens parameters
The following are some of the parameters related to common Sony-grade DSLR lenses: ** 1. Focus ** 1. ** SonyMDT18 - 135mmF3.5 - 5.6Sam**: The focal length range is 18 - 135mm. 2. ** PE PZ 28 - 135mm F4G OSS**: focal length 28 - 135mm. 3. ** ESF-S 18 - 200**: The focal length range is 18 - 200mm. 4. ** Sony70 - 400mm F4 - 5.6G SSM**: The focal length range is 70 - 400mm. 5. ** SonyFE24 - 240mmF3.5 - 6.3OSS**: The focal length range is 24 - 240mm. 6. ** SonyFE24 - 70mmF2.8GM**: The focal length is 24 - 70mm. 7. ** SonyFE24 - 105mmF4 **: The focal length range is 24 - 105mm. ** 2. Maximum aperture ** 1. ** SonyMD18 - 135mm F3.5 - 5.6Sam**: It is a floating aperture lens, and the maximum aperture changes between F3.5 - 5.6. 2. ** PE PZ 28 - 135mm F4G OSS**: A constant aperture lens with a maximum aperture of F4. 3. ** ESF-S18 - 200**: The maximum aperture is F2.8. 4. ** Sony70 - 400mm F4 - 5.6G SSM**: It is a floating aperture lens, and the maximum aperture varies between F4 - 5.6. 5. ** SonyFE24 - 240mmF3.5 - 6.3OSS**: It is a floating aperture lens, and the maximum aperture changes between F3.5 - 6.3. ** 3. Identification and characteristics of the lens type ** 1. ** PE **: E-mount full-frame lens, suitable for all E-mount devices. 2. **E**: E-mount APS-C frame lens, can be installed on all E-mount devices, but when paired with a full-frame camera, there will be frame trimming by default (only the central part of the CPU is used). If the image is not trimmed, there will usually be obvious halation or black blocking. 3. **G**: Inherited from Minolta's high-end lens logo, most of them have nano-coating. 4. **ZA**: A lens product jointly developed by Sony and Zeiss. The lens body and packaging have the double logo of Sony and Zeiss, all with T* coating. The lens may also have the words representing the lens structure (such as Warrio-Tessar, Planer, Distagon, Sonnar, etc.). There is no new product since July 2016. 5. GM (G-Master or "G-Master"): It was the highest-end lens product line from Sony, and all of them were nano-coated. ** 4. Other characteristics ** 1. ** PE PZ 28 - 135mm F4G OSS**: It has a power zoom function, which can provide smooth angle conversion and anti-shake function. 2. ** ESF-S18 - 200**: Automatic focus and anti-shake support. 3. ** Sony70 - 400mmF4 - 5.6G SSM**: It has SSM (ultrasonic motor), which is good for autofocus operation. 4. ** SonyFE24 - 240mmF3.5 - 6.3OSS**: With OSS (optical image stabilization system). <a href="/?from=ask_words" style="color:red" target="_blank">Read more exciting novels for free</a>