Single-phase two-speed induction motor connection methods include star connection and triangle connection. In the star connection, the motor speed is lower, suitable for lower load situations; in the triangle connection, the motor speed is higher, suitable for higher load situations. For a single-phase two-speed induction motor with five circuit output ends,(One of the leads is the common end of the winding, and the other four leads are the lead ends of the main and secondary winding of the 12-pole winding and the 2-pole winding respectively). There is also a case of a 5-wire single-phase motor. The black and yellow are a group (connected to a transformer, and the transformer is a non-polar transformer). The black wire is connected to the power supply, and the yellow wire is thrown aside after being connected. Red, white, and blue correspond to three speeds (red corresponds to fast speed, white corresponds to medium speed, and blue corresponds to low speed). However, attention should be paid to the connection. The appropriate connection method should be selected according to the specific load situation, and the accuracy of the connection should be ensured to ensure the normal operation of the motor. Read more exciting novels for free
There were different types of single-phase motor, and the method of connecting the voltage to the voltage was also different: 1. ** General Judgment Method **: - The single-phase motor had a main coil and a secondary coil. The resistance of the main coil was smaller than that of the secondary coil. Usually, the connection method can be determined by measuring the resistance between the motor leads. The two wires with the highest resistance were connected to the power source. 2. ** Connection under different starting modes ** - ** Split-phase start type **: suitable for electric fans, air-conditioner fan motor, washing machine and other motor. The auxiliary starting winding is used to assist the starting. The starting moment is not large, and the running speed is roughly maintained at a fixed value. - ** Starting method with centrifugal switch (two conditions)**: - In the first case, when the motor is still, the centrifugal switch is connected. After the power is supplied, the starting capacity will participate in the starting work. When the speed of the motor reaches 70% - 80% of the rated value, the centrifugal switch will automatically trip, and the starting capacity will be disconnected. The starting winding will not participate in the operation work, and the motor will continue to operate with the running winding coil. - In the second case, when the motor is still, the centrifugal switch is connected, and the starting capacity is involved in the starting work after the power is supplied. When the speed of the motor reaches 70% - 80% of the rated value, the centrifugal switch will automatically trip, and the starting capacity will complete the task and be disconnected. The running capacity is connected to the starting winding in series to participate in the operation work. This kind of connection was generally used in places with large and unstable loads such as air condensers, cutting machines, and woodworking machines. 3. ** Connection of the motor with different number of lead wires ** - ** 3 wires of AC 220V induced draft fan (motor as an example)**: First measure the values between the wires of the motor, such as red and blue resistance 381, red and yellow resistance 828, yellow and blue resistance 447. Since red and blue 381+ yellow and blue 447 = red and yellow 828, it can be judged that the starting winding has a high resistance (red and yellow wire) and the running winding has a low resistance (red and blue wire). Then connect the red and yellow wire to the capacity and the red and blue wire to the power supply. - ** Four wires of AC 220V motor (connection method)**: measure the value between each two wires respectively. For example, the resistance value of green and black is 0, the resistance value of red and black is 2.57, the resistance value of red and yellow is 0, and the resistance value of yellow and green is 2.65. The resistance value between green and black and red and yellow is infinite, which means that it is impossible. There are clear values between red and black and yellow and green, which means that there are two separate sets of winding and they are not connected. The yellow and black wires could be connected together as the common end, and the capacity could be connected to both ends of the red and green wires. The common end wire and any of the red and green wires could be connected to the power supply, and the motor with positive and negative rotation could be obtained. - ** AC 220V single-phase double-cap motor **: Pay attention to the selection of starting and running caps. The larger capacity was the starting capacity, and the smaller capacity was the running capacity. After the motor starts, the centrifugal switch disconnects the starting capacity from the circuit. If there is a lack of starting capacity, the motor will be difficult to start or unable to start (often manifested as normal no-load start, but unable to start after loading); if there is a lack of running capacity, the motor can start, but the output power will be reduced (often manifested as reduced load capacity). Generally, the starting capacity was connected in series to the starting winding of the single-phase motor and in parallel with the working winding. In addition, if the motor needs to be reversed, for the above-mentioned connection method, it is only necessary to swap the wires of the corresponding winding. In some cases, the 1 - 2 wire swap or the 3 - 4 wire swap can complete the reversal. <a href="/?from=ask_words" style="color:red" target="_blank">Read more exciting novels for free</a>
There were two ways to connect the four wires of a single-phase motor, the star connection and the triangle connection. Star connection is mainly used for low-power motor, starting current is small, but starting moment is also small; triangle connection is mainly used for high-power motor, starting current is large, but starting moment is also large. You can check the label on the motor shell or check the motor manual to determine the motor's connection method. Generally speaking, the star connection is marked with "Y" or "Delta/Y", and the triangle connection is marked with "Delta" or "Y/Delta". It should be noted that among the four wires of the single-phase motor, the main wire is the power supply wire of the motor, and the auxiliary wire is used to start the motor. There were four wires because the single-phase motor needed to be started by a starting reactor or a starting reactor. These starting components needed to be connected to the motor, thus increasing the number of wires in the motor. If the four wires of the single-phase motor were connected wrongly, it might cause the motor to fail to start normally or damage the motor. If you find that the connection is wrong, you should stop using it in time and ask a professional to repair and correct the connection. <a href="/?from=ask_words" style="color:red" target="_blank">Read more exciting novels for free</a>
There are several ways to connect a single-phase frequency changer to a single-phase ordinary motor: 1. ** Series Condenser Method **: A single phase motor is connected in series with a single phase motor's starting circuit. The phase is shifted so that the motor's rotation is not zero to achieve the start. However, when connecting the single-phase motor to the frequency changer, some prerequisites must be met, such as removing the transformer, the starting winding and the working winding of the single-phase motor must be the same (that is, the resistance must be the same), if it is a 380V frequency changer, the highest output voltage must be set to 220V, the frequency changer should cancel the output phase detection function, and the driven frequency changer must be at least one level larger than the motor. 2. Split-phase method: Divide the winding of a single-phase motor into two parts, and then connect these two parts of the winding to the two output ports of the frequency changer, so as to achieve the start and operation of the motor. 3. ** frequency conversion method **: The alternating current signal of the single-phase power supply is converted into a high-frequency pulse signal by the frequency changer, and then it is turned into a single-phase alternating current power supply through the filter circuit to realize the start and operation of the single-phase motor. The connection between a single-phase frequency changer and a single-phase motor mainly had two types: direct connection and indirect connection. The direct connection method was to connect the output of the single-phase frequency changer directly to the input of the single-phase motor; the indirect connection method was not mentioned in detail. In addition, the three-phase input frequency changer input is generally R, S, T three terminal, the connection is not divided into phase order; only labeled R, T frequency changer is a single-phase input frequency changer, one connected to the live line, one connected to the neutral line (zero, live line is not distinguished); Some frequency changers labeled with R, S, T three input terminal also allow single-phase input, at this time, any two terminal can be connected to AC220V. It should be noted that the frequency conversion control of single-phase motor should be matched and set according to the specific model of the motor and the frequency changer. Before operation, you should carefully read the manual and abide by the safety regulations. <a href="/?from=ask_words" style="color:red" target="_blank">Read more exciting novels for free</a>
For the single-phase fan motor winding connection, the first thing to do was to determine the main and auxiliary winding of the motor and the common wire. The resistance between the three wires of the motor could be measured by a Multimeter. Three different resistance values would be obtained. The two wires with the highest resistance value were the sum of the resistance values of the main and secondary winding, and the remaining wire was the common wire. Then, the common wire was used to measure the resistance of the main and secondary winding respectively. The lower the resistance, the main winding would be the main winding, and the higher the resistance, the secondary winding would be the secondary winding. If it was a three-wire motor, the resistance between the two could be measured by a Multimeter. The two wires with the largest resistance were connected to the capacity, and the remaining wire was connected to the neutral line of the power supply. Finally, the direction of the motor could be adjusted by connecting the live wire to any one of the two capacity wires. If it was a 5-wire motor, black and yellow would be a group, and red, white, and blue would be a group. The black and yellow wires were connected to the power supply, while the yellow wire was connected to the power supply. Red, white, and blue corresponded to the three speeds. Red corresponded to fast speed, white corresponded to medium speed, and blue corresponded to low speed. There was another method of connection: the live wire was divided into two paths, one path to the main winding and then back to the neutral line, and the other path to the secondary winding and back to zero. <a href="/?from=ask_words" style="color:red" target="_blank">Read more exciting novels for free</a>
Two-phase motor single-capacity four-wire connection method is as follows: 1. The main coil of the two-phase motor was connected to L1 and L2 of the power supply. 2. The auxiliary coil of the two-phase motor was connected to L1 of the power supply. 3. One end of the transformer was connected to L2 of the power supply, and the other end was connected to the auxiliary coil of the two-phase motor. 4. A starting reactor is connected between the main coil and the auxiliary coil of the two-phase motor. 5. Ground the casing of the two-phase motor. <a href="/?from=ask_words" style="color:red" target="_blank">Read more exciting novels for free</a>
Connection of the three-phase motor: According to the power supply voltage and nameplate identification, the three-phase motor is connected to the star connection or the angle connection in the junction box. There were two rows of six terminal blocks in the junction box. When star connection was used, the three terminal blocks on the top of the junction box were short-circuited with a short-circuit piece, and the three terminal blocks on the bottom row were connected to the three-phase power supply respectively. When corner connection was used, the upper and lower rows of terminal blocks were connected vertically, and then the three-phase power supply was connected respectively. Single-phase motor connection: For a single-phase motor with relatively small power (such as a fan, washing machine, etc.), one end of the primary and secondary coil is connected together, and three terminal are led out. Only one voltage is needed (the starting voltage and the running voltage are integrated). Use a Multimeter to measure any two of the three terminal blocks of a single-phase motor. Three sets of values can be obtained. The two terminal blocks with the largest resistance value of the capacity and the two terminal blocks with the small resistance value of the zero line and the live line (the zero line and the live line can be interchanged). If you want to reverse it, you can change the line connected to one end of the capacity to the other end of the capacity. For a single-phase motor with high power, the main and auxiliary coil were separated, and the centrifugal switch had a total of 6 connecting terminal. First, ensure that the motor winding terminal was arranged in a specific way. At this time, the resistance of the two terminal of the auxiliary winding was the largest, the resistance of the two terminal of the main winding was second, and the resistance of the two terminal of the centrifugal switch was 0 Omega. Then, the connection was made according to the regulations. If the motor was to be reversed, the connection method of the specific connecting terminal needed to be changed. However, the connection method of four-wire motor to connect three-phase and single-phase was not found. If the four-wire motor refers to the motor connection under the three-phase four-wire system, the three-phase connection shall be based on the above-mentioned connection method of three-phase motor. For single-phase, you can refer to the connection method of single-phase motor and take one phase of live wire and zero wire from the three-phase four-wire for connection. <a href="/?from=ask_words" style="color:red" target="_blank">Read more exciting novels for free</a>
In the five-wire single-phase motor, three wires were the main wire, one was the starting wire, and one was the auxiliary wire. Generally, the following methods can be used to connect the voltage: First, distinguish the main winding, the secondary winding, and the starting line of the motor. Generally speaking, the main winding was connected to the power supply, and the secondary winding was connected to the voltage. For the case of five wires, it could be judged by measuring the resistance value first. The two wires with the highest resistance value were connected to the capacity (one of them was the secondary winding wire, and the other was the auxiliary wire such as the starting wire), and the one with the lowest resistance value was connected to the power supply of the main winding wire. If you want to change the direction of the motor, you can swap the specific wires in the motor's lead wire (such as swapping the wire connected to the transformer with other related wires), but the specific operation still needs to be carefully adjusted according to the actual structure and function of the motor. <a href="/?from=ask_words" style="color:red" target="_blank">Read more exciting novels for free</a>
The following methods can be used to judge the quality of a two-speed single-phase motor: 1. Check the power supply of the motor: First of all, check whether the power supply of the motor is normal. If there is a problem, you can use the voltage meter to check. 2. Check the motor's transformer: The transformer is an important part of the single-phase motor. If you suspect that it is damaged, you can use the transformer tester to check it. 3. Check the motor winding: The motor winding is the core part of the motor. If the winding is short-circuited or open, you can use a Multimeter to check the motor winding. The red and black probes of the Multimeter were inserted into the winding terminal of the motor to detect the resistance of the over-temperature protector, the winding with different pole numbers (such as 12-pole winding, 2-pole winding), and the resistance between these winding and the common terminal. Under normal circumstances, the resistance between the 2-pole winding is approximately equal to the sum of the resistance between the 2-pole winding and the common end of the winding, and the three sets of resistance between the 12-pole winding and the common end of the 12-pole winding are all tens of Ohms. If a pair of resistance values is found to be infinite during the test, it means that there is a break in the winding; if the three sets of values do not meet the above equation relationship or have a large deviation from the normal value, it means that there may be a fault in the winding, such as a short circuit between the winding. At this time, it should be considered to replace the motor. 4. Checking the bearing of the motor: The bearing of the motor is an important part of the motor. If the bearing is worn or damaged, you can use the hand to check the bearing of the motor. <a href="/?from=ask_words" style="color:red" target="_blank">Read more exciting novels for free</a>
The principle difference between a single-phase motor and a three-phase motor is as follows: 1. * * Power supply **: Single-phase electricity consists of a live wire and a neutral wire. Single-phase electric motor uses single-phase power. Three-phase electricity has three phase lines, which are three-phase four-wire (three live wires and one zero wire). Three-phase electric motor uses three-phase power. 2. * * Stator winding structure and distribution ** - * * Three-phase motor **: Stator winding is composed of three-phase winding with a difference of 120 electrical angles in physical space. After the three-phase symmetrical alternating current was introduced, a theoretically circular rotating magnetic field was formed. The rotating magnetic field cuts the winding of the motor, and an induced current is generated in the winding of the motor. The current carrying conductor of the motor generates electromagnetic force under the effect of the rotating magnetic field of the motor, and the direction of rotation of the motor is the same as the direction of the rotating magnetic field. - * * Single-phase motor **: Stator winding is generally composed of a main winding and a secondary winding (taking a single phase motor as an example). The main winding and the starting winding were separated by 90 degrees in space. The starting winding was connected in series with a suitable capacity, so that the current of the main winding was approximately 90 degrees different in phase, forming a phase-splitting or phase-shifting principle. Two currents that were 90 degrees different in time and space were passed into the two winding, creating a rotating magnetic field that automatically started the generator. After starting, the speed of the engine will rise to a certain level, and the starting winding will be disconnected with the help of a centrifugal switch or other automatic control device. Only the main winding will work during normal operation. 3. * * The influence of the rotating magnetic field on the activation ** - * * Three-phase motor **: The three-phase power supply can be directly connected to the three-phase winding to generate a rotating magnetic field. This rotating magnetic field can make the motor start and run smoothly without the need for additional auxiliary devices (such as a transformer) to generate a rotating magnetic field. - Single-phase motor: When a single-phase Sinusoid current flows through the winding, it produces an alternating pulsating magnetic field. It can be seen as two rotating magnetic fields with the same speed and opposite directions. This makes the motor unable to rotate when the motor is at rest due to the two equal and opposite torques. Therefore, a special method was needed to generate a rotating magnetic field to start, such as adding a starting winding to the stators and connecting the starting winding in series (a single phase motor), or using the shaded pole method (a shaded pole motor). 4. * * Field of application **: Single-phase motor is more used in living places, and three-phase motor is mostly used in industrial fields. <a href="/?from=ask_words" style="color:red" target="_blank">Read more exciting novels for free</a>
The single-phase voltage regulating type infinitely variable speed motor's stators had two sets of winding, each set of winding was separately wound on a pair of independent magnetic poles, and the two sets of winding were evenly distributed on the stators. One set of winding is connected to the single-phase alternating current power supply, and the other set of winding is connected to the single-phase alternating current power supply after the phase shift of 90 degrees by the transformer. The motor has the advantages of simple structure, convenient manufacturing, high power factor, good speed regulation characteristic, wide speed regulation range, etc. By adjusting the power supply voltage of the motor, the speed of the motor can be infinitely adjusted. It can be applied to various household appliances, electric tools, traction motor of electric locomotive, etc. <a href="/?from=ask_words" style="color:red" target="_blank">Read more exciting novels for free</a>