The reaction between the alcoholic group and the solution was an alkali-base reaction, which was accompanied by the protonation of the alcoholic group and the deprotonation of the solution. In the reaction, the hydrogen atom in the alcoholic group was replaced by the alcoholic group in the sulfuric acid, forming water and a positively charged ion. At the same time, the negative ion in the sulfuric acid combined with the positively charged ion in the alcoholic group to form a salt. The reaction equation was: <<p>><p></p>><p></p>><p><p>><p><p>><p><p>><p><p>><<p>><p> p>><p>> p> p>>& gt In general, because the alcoholic group was weakly acidic, it could react with the strong base, namely, soda. It did not require any special reaction conditions and could react at any time. <a href="/?from=ask_words" style="color:red" target="_blank">Read more exciting novels for free</a>
It could react with sulfuric acid. The reason for the reaction between the two was that sulfuric acid had the ability to be acidic and could be used as a catalyst. From an acidic point of view, sulfuric acid could provide hydrogen ions to react with the ether. From the perspective of the sulfuric acid reaction, the sulfuric acid group (-SOH) in sulfuric acid could replace the hydrogen atom on the aromatic ring of the sulfuric acid. This was because the electron cloud density of the aromatic ring in the sulfuric acid was relatively high, and it was easy to be attacked by electrophiles (such as the sulfuric acid group in sulfuric acid), resulting in an electrophilic substitution reaction, which was the sulfuric acid reaction. During the reaction, different products would be produced depending on the reaction conditions. For example, it may produce p-hydrylsulfuric acid; if the reaction conditions are not properly controlled, because of the reduction of the ester and the oxidisation of the concentrated sulfuric acid, the ester may be oxided by the concentrated sulfuric acid into p-methylazone, and the p-hydrylsulfuric acid may be further Sulfonated to form 4 -hy- 1,3 -besilenedisulfuric acid. In order to prevent the sulfuric acid from evaporating the sulfuric acid during the process of sulfuric acid, the reaction temperature should be controlled to not exceed 90 ° C, and the concentrated sulfuric acid with a concentration of not more than 85% should be used. Other sulfuric acid could also be replaced by other sulfuric agents such as sulfur dioxide. <a href="/?from=ask_words" style="color:red" target="_blank">Read more exciting novels for free</a>
In the experiment of preparing ethvl acetate, the order of addition of the reagents was as follows: alcohol, concentrated sulfuric acid, and ethvl acetate. The main reason was that the density of concentrated sulfuric acid was higher than that of alcohol, and when concentrated sulfuric acid was mixed with alcohol, it would release a lot of heat. If the concentrated sulfuric acid was added first and then the alcohol was added, due to the high density of the concentrated sulfuric acid, the heat would quickly accumulate at the bottom during the mixing process, which would easily cause the liquid to splash and cause danger. Adding alcohol first, then slowly adding concentrated sulfuric acid, could make the heat more evenly distributed. The reason why the last step was to add the sulfuric acid was because it was more volatile than the concentrated sulfuric acid. If the sulfuric acid was added first, the heat generated during the process of adding the concentrated sulfuric acid might cause a large amount of the sulfuric acid to evaporate, affecting the reaction yield. <a href="/?from=ask_words" style="color:red" target="_blank">Read more exciting novels for free</a>
Usually, they would not react with each other. They could coexist in water solutions. For example, in a solution of sulfuric acid, there were both sulfuric acid ions and sulfuric acid ions. However, in different environments, their existence and interaction would be different. In an acidic environment, the radical ions would combine with hydrogen ions to form water. In an acidic environment, both radical ions and sulfuric acid ions would exist, but the radical ions would be replaced by hydrogen ions in the base to form water. In an electrochemistry reaction, the reduction potential of the hydrogen ions was higher than that of the sulfuric acid ions. Therefore, the hydrogen ions would first accept electrons and be reduced to water molecules, while the sulfuric acid ions would be discharged later. <a href="/?from=ask_words" style="color:red" target="_blank">Read more exciting novels for free</a>
The reaction equation for the reaction between the acid and the acid is: Mn (NO2) 2 + H2SO2 = Mn (NO2) 2 + 2HNO2. There was no information that stated that this reaction could not be used, so it was impossible to accurately answer why this reaction could not be used. <a href="/?from=ask_words" style="color:red" target="_blank">Read more exciting novels for free</a>
The reaction equation is: NaH + CH30H → CH3ONa +H2O. This reaction was a strongly irreversible reaction. <a href="/?from=ask_words" style="color:red" target="_blank">Read more exciting novels for free</a>
The reaction between the acid and the acid could produce a solution of the acid, and the reaction equation was: Mn (NO3)2+ H2SO4 === ZnSO4 + 2HNO3. <a href="/?from=ask_words" style="color:red" target="_blank">Read more exciting novels for free</a>
When iron reacted with the mixed solution of sulfuric acid and copper sulfuric acid, there was no problem of who reacted with iron first. This was because sulfuric acid and copper sulfuric acid were uniform solutions, and it was impossible to determine which iron would come into contact with first. This kind of mixture reaction was a competitive reaction. The iron would react with whichever ion it came into contact with first. Although Cu2 was more oxidisable than H, hydrogen could not reduce Cu2 in the water solution, so there was no order. <a href="/?from=ask_words" style="color:red" target="_blank">Read more exciting novels for free</a>
Sulfuric acid and sulfuric acid did not react. The crystals were colorless, and the solid powder was white. This color was its own physical properties, not caused by the reaction between sulfuric acid and sulfuric acid. <a href="/?from=ask_words" style="color:red" target="_blank">Read more exciting novels for free</a>
The reaction between iron and copper sulfuric acid would not produce iron sulfuric acid. When iron reacted with copper sulfuric acid, iron was more mobile than copper, and a replacement reaction occurred. The iron atom lost two electrons and became a Fe2 ion, while the copper ion (Cu2) gained two electrons and was reduced to a copper atom. The reaction equation was: FeSO = FeSO + Cu2, and the product was FeSO, not Fe2 (SO). This is because in this reaction, iron is mainly oxided to iron ions instead of iron ions. <a href="/?from=ask_words" style="color:red" target="_blank">Read more exciting novels for free</a>