It could be nitrated with concentrated sulfuric acid to form 2,4,6-trinitrotoluene. Read more exciting novels for free
When the reaction of the solution of excessive amount of potassium moons and concentrated sulfuric acid was carried out, the pale yellow crystals of phosphorus moons would be formed. The reaction equation was: PO4 ^3- +12MoO4 ^2- + 3NH4^+ + 24H^+= (NH4)3(P(Mo12O40))·6H2O → +6H2O. This was the characteristic reaction for identifying phosphorus radical. <a href="/?from=ask_words" style="color:red" target="_blank">Read more exciting novels for free</a>
The aluminum would react with concentrated sulfuric acid and concentrated sulfuric acid. In the early stages of the reaction, a small amount of aluminum dioxide would be formed. Later, a dense layer of aluminum dioxide would form on the surface of the aluminum, preventing the reaction from proceeding further. This phenomenon was called detoxification. Condensed sulfuric acid and concentrated sulfuric acid were corrosive and dangerous chemicals, but there was not enough information to show whether the products formed by the reaction of aluminum with them were toxic. It was impossible to accurately answer whether the reaction products were toxic. <a href="/?from=ask_words" style="color:red" target="_blank">Read more exciting novels for free</a>
Both concentrated sulfuric acid and concentrated sulfuric acid could react with iron. Iron and concentrated sulfuric acid would undergo a " passive " phenomenon at room temperature, that is, a dense oxide-film would form on the surface of the iron, causing the reaction to stop. There would be no obvious reaction. However, under heating conditions, a reaction would occur, and iron sulfuric acid and sulfur dioxide would be formed. When the reaction was almost over, iron sulfuric acid and hydrogen would be formed. When iron and concentrated sulfuric acid were at room temperature, the iron would be deactivated by concentrated sulfuric acid, and a dense oxygen film would form on the surface to prevent the reaction from continuing. There would be no obvious reaction. The reaction could be carried out under heating, because the dense oxide-film was destroyed. <a href="/?from=ask_words" style="color:red" target="_blank">Read more exciting novels for free</a>
Acetic anhydryride-concentrated sulfuric acid reaction (Liebermann-Burchard reaction) can be used to identify tripenoid and steroid side. The specific identification method was as follows: dissolve the sample in vinegar and add concentrated sulfuric acid-vinegar (1:20). If the final color was red or purple, it was triterpene soap. If the final color was blue-green, it was steroid soap. During the reaction process, color changes such as red → purple → blue → green → dirty green would occur in turn, and finally the color would fade. <a href="/?from=ask_words" style="color:red" target="_blank">Read more exciting novels for free</a>
Under normal conditions, ester and concentrated sulfuric acid would not react, so there was no reaction equation. <a href="/?from=ask_words" style="color:red" target="_blank">Read more exciting novels for free</a>
Under the catalyst of concentrated sulfuric acid, 1 mole of aromatic acid and 1 mole of concentrated sulfuric acid reacted to form 1 mole of nitrogen and 1 mole of water. The reaction formula was: C6H6 (aromatic ring)+ HNO3 + H2SO4 (catalyst) → C6H5-NO2 + H2O. If it was to form m-dinitro, the reaction formula was: C6H6 + 2HNO3--> C6H4 (NO2) 2 (dinitro is in the meta-position)+2H2O. <a href="/?from=ask_words" style="color:red" target="_blank">Read more exciting novels for free</a>
Mercury can react with concentrated sulfuric acid, but if there is water in the system, the concentrated sulfuric acid will not react with mercury after being diluted. Moreover, even if the two reacted to form mercury sulfuric acid, mercury sulfuric acid would react with these metals when it passed through iron or copper sewer pipes, which was similar to the effect of mercury being washed away. Mercury had a low chemical reaction and reacted weakly with most acids. <a href="/?from=ask_words" style="color:red" target="_blank">Read more exciting novels for free</a>
At room temperature, concentrated sulfuric acid would have a slow corrosive effect on the polythene, and at 90 - 100 ° C, concentrated sulfuric acid would rapidly erode the polythene, causing it to be destroyed or decomposed. <a href="/?from=ask_words" style="color:red" target="_blank">Read more exciting novels for free</a>
The reaction equation for the reaction between ethene and concentrated sulfuric acid was: CH2 = CH2 + H2SO4 → CH3CH2OSO3H. In chemistry, there was no reaction without heating or concentration, such as the reaction between carbon and concentrated sulfuric acid or concentrated sulfuric acid, the reaction between copper and concentrated sulfuric acid. The reaction between ethene and concentrated sulfuric acid was not mentioned. However, according to the laws of chemistry, ethene had a certain degree of reduction, and concentrated sulfuric acid had strong oxidization. Under certain conditions, the two could react. <a href="/?from=ask_words" style="color:red" target="_blank">Read more exciting novels for free</a>
No, the reaction between copper and concentrated sulfuric acid was not a disproportionate reaction. The reaction equation between copper and concentrated sulfuric acid is: [Cu +2H ^SO2 (concentrated)][stacking]{heating}{=] CuSO + SO2 ^+2H2O). In this reaction, the valency of copper increases from 0 to +2 and is oxided, and the valency of sulfur in concentrated sulfuric acid decreases from +6 to +4 and is reduced. This reaction belongs to the type of reduction reaction in the oxidoreduction reaction. Disproportionation reaction refers to the reaction where if the oxidofication and reduction occur on an element in the same molecular state, part of the atoms (or ions) of the element will be oxided. The other part was restored. <a href="/?from=ask_words" style="color:red" target="_blank">Read more exciting novels for free</a>